Breaks a compound object into its component objects break command scale command champfer command explode command

Q: is an AUTOCAD command which is used to draw a portion of the ........ circumference of a circle. a)…

A: Finding out AutoCAD command for given statement.

Q: The second floor of a light manufacturing building is constructed from a 125 mm thick stone concrete…

A:

Q: Q.4 An example simple truss is shown in Figure. The deck in this bridge is concurrent with the…

A:

Q: top, front and side view on autocad

A: To draw the top, front and side view of the given figure.

Q: Which of the following factors will increase the effectiveness of disinfectant? 1. Temperature 2.…

A: Disinfectant- Any drug or method that kills germs, including viruses, bacteria, and other microbes…

Q: of nsions? O Option 1

A: Option 1,2, 3 does not completely give the dimensions of their respective figures.

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: Problem Number 1: In the given composite structural section determine the quantities placed in the…

A:

Q: CAD is used to

A: You need to familiarize yourself with a range of civil engineering programme, if you are interested…

Q: Consider the frame shown in (Figure 1). There is a pulley at E, a smooth slot at C, a pin at B, and…

A: The frame shown in below figure,  there is a pulley at E, a smooth slot at C, a pin support at B and…

Q: A water treatment plant of capacity, 1 m³/s has filter boxes of dimensions 6 mx 10 m. The loading…

A: Given data- A water treatment plant- Capacity of plant Q=1 m3/s, Dimension of the filter boxes = 6…

Q: Water flows at a rate of 120 L/s in a 30 cm diameter horizontal pipe connected to a 20 cm diameter…

A: Given discharge= 120 L/s  Dia of horizontal pipe = 30 cm  Dia of vertical pipe = 20 cm

Q: Q.1) For the plate shown in figure, determine the forces in three ropes if the plate weighs 1.6 kN.…

A: Solution:

Q: Problem 12.16 Consider the building frame shown in (Eure) Suppose that My 2.6 k/ft and s8 k/ft.…

A:

Q: The distance from the principal point to an image on a photograph is 6.44 cm and the elevation of…

A:

Q: A 20 mm diameter bar is 1.25 m long. When the bar is simply supported at its ends in a horizontal…

A:

Q: What is D30 (or D10 or D 60)?

A: D10, D30, D60 refers to:D10 = particle size (diameter in mm) at which 10% of soil mass finer than…

Q: C. A normal weight reinforced concrete square footing (6ft x 6ft) has a total depth of 20 in. It…

A: C. Solution:   The critical section is permitted to be at the face of the column Mu=qu(l-c2)2×b2=144…

Q: Which shortcut key lets you rotate the drawing area? RO О тв O z O L

A:

Q: On Autocad, what is the difference between polyline and line?

A: The major difference between Line and Polyline(PLine) , That the line command, fetches the line…

Q: Figure, 50mm 50mm 50mm 50mm 250mm N.A C.g 100mm 93 100mm 100mm

A:

Q: The body on the incline in Fig. 5 is subjected to the vertical and Horizontal Forces shown. Find the…

A: tan θ = 24 θ = 26.56° 90° - θ = 90° - 26.56° = 63.44°

Q: Determine the slope at A and deflection at C in the beam shown below: Take the last two digits of…

A:

Q: Differentiate b/w the following: i) Ultimate limit states & Serviceability limit states ii) UBC &…

A: Answer:- Serviceability limit state: To satisfy the serviceability criteria, a structure should…

Q: Given. d₁=20cm or d₂ 20cm or C = 0·80 For Rectangular port, t₁ = "S" Adh ₂ 21h 1-8 3 4₁ = 2021-125/1…

A:

Q: ESSAY Advantages and Disadvantages of Using Hollow Block

A: Hollow blocks are generally prepared with aerated concrete . These block have both advantages as…

Q: In .... mode, cursor movement is constrained to the horizontal or vertical direction relative to the…

A: e)Ortho In Ortho mode, cursor movement is constrained to the horizontal or vertical direction…

Q: V Discuss strain hardening covering its significance in the context of plastic deformation and…

A: Strain hardening:- Strain hardening is generally defined as heating at a relatively low temperature…

Q: 45 KN/m 200 50 KN A 9.00 m RB 3.50 m 150 KN-m

A:

Q: Differentiate b/w the following:   i) Ultimate limit states & Serviceability limit states

A: The ultimate limit state is the design for the safety of a structure and its users by limiting…

Q: 3001bsC 10 ft 15001bs

A: Solution:- Support reactions R1, R2, and R3 are shown in figure. Now, horizontal reaction R2=RDx is…

Q: For the lap joint, defermine The maximua safe lond P. which may be aylied t the average tedeile…

A: Given, Diameter of rivet, d = 25 mm t= 25 mm Width of the plate, w= 125 mm No. of rivet = 3 Average…

Q: For the truss shown, determine the stress in members AC and BD. The cross-sectional area of each…

A:

Q: subtract the numbers 557                                   -125

A: The process of deduction of quantity is known as subtraction.