block brake consists of a pin-connected lever and friction block at B. The coefficient of static friction between the wheel and the lever is μs = 0.3, and a torque of 5 N ⋅m is applied to the wheel. Determine if the brake can hold the wheel stationary when the force applied to the lever is (a) P = 30 N, (b) P = 70 N   Draw the free-body

Q: The figure shows a part of a machine used to crush recycled cans. Link ABC is attached to the ground…

A:

Q: The brake is to be designed to be self locking, that is, it will not rotate when no load P is…

A:

Q: The two blocks used in a measuring device have negligible weight. The spring is compressed 4 in.…

A:

Q: The 107-lb force P is applied to the 220-lb crate, which is stationary before the force is applied.…

A:

Q: 0.15.

A:

Q: 8-93. The simple band brake is constructed so that the ends of the friction strap are connected to…

A:

Q: The uniform concrete block in (Figure 1) has a weight of 300 lb. The coefficients of static friction…

A: iven Data:

Q: The brake is to be designed to be self locking, that is, it will not rotate when no load P is…

A: Given data:-coefficient of static friction at b for self-locking condition p = 0 NTo finddistance d…

Q: Determine whether the block shown below is in equilibrium, and find the magnitude and direction of…

A: Given:  The coefficient of static friction is μs=0.30,  The coefficient of kinetic friction is…

Q: A roll of paper has a uniform weight of 2kN and is suspended from the wire hanger so that it rests…

A: Given, Weight of the roll paper = W = 2 kN Angle θ = 30o Coefficient of friction = μ = 0.3 Radius of…

Q: The coefficient of static friction between the 65-lb roller and the ground is μ = 0.2. Fins the…

A: Given data: w=65 lbμs=0.2r=3 ft2=1.5 ftP=Pmax=?

Q: he block brake consists of a pin-connected lever and friction block at BB. The coefficient of static…

A:

Q: The coefficients of static and kinetic friction between the drum and brake bar are μS= 0.4 and μK=…

A: Given The coefficient of static friction is μs=0.4. The coefficient of kinetic friction is μK=0.3.…

Q: PROBLEM 1: Two blocks A and B, each having a mass of 5 kg, are connected by the linkage shown in the…

A: Step 1:Step 2:Step 3:Step 4:

Q: The wheel is subjected to a torque of M 50 N m. If the coefficient of kinetic friction between the…

A:

Q: The crate shown is held against wedge B by a spring. The spring is 93.5% of its original…

A:

Q: 5 ft B N 1.5 f

A: given-         uniform concrete block in (Figure 1) has a weight of 300 lb. The coefficients of…

Q: The mine car and its contents shown in (Figure 1) have a total mass of 4.5 Mg and a center of…

A:

Q: If the clamping force at G is 900 N, determine the horizontal force F that must be applied…

A: The clamping force at G is .The mean diameter of thread is .The lead is .The static coefficient of…

Q: The high strength, square-threaded bolt that holds the three plates together has a nominal diameter…

A:

Q: The hand clamp is constructed using a square-threaded screw having a mean diameter of 36 mm, a lead…

A: The force applied is .The coefficient of friction at the screw is .The mean diameter is .The lead is…

Q: The shaft has a square-threaded screw with a lead of 8 mm and a mean radius of 15 mm. If it is in…

A: T= 7 N-m or 7000 N-mmL=8 mmrscrew=15 mmrgear=30 mmμ=0.2

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.