Block B is on top of an inclined plane and is being supported by Rod AB, which is attached to Block A. The weight of Block A is 40 KN, and the weight of Block B is 80 KN. Force F prevents the block from sliding. Determine the Normal Force N of the surface that supports Block A. Neglect all friction.

Q: The flat band that goes from pulley A to pulley B has a coefficient of static friction us=0.4, it…

A:

Q: The 1.2-kg wooden block is used for level support of the 9-kg can of paint. Determine the magnitude…

A: Given:-           To calculate the angle θ                           θ = tan-1412   = 18.435°

Q: While digging a small hole prior to planting a tree, a homeowner encounters rocks. If he exerts a…

A:

Q: 3. Determine the smallest horizontal force P that would push the homogenous cylinder of weight W…

A: As per given question  We have to find force required to puah the cylinder

Q: A B

A:

Q: Question 2 Given each block has a mass m. The coefficient of kinetic friction at all surfaces of…

A:

Q: Determine the maximum downward force Pmax that can be applied to wedge A that wil keep the assembly…

A: Given: The weight of block C, W = 192 N

Q: hãi 30 The ladder AB Support at smooth surface at A and at rough surface at B, if the coefficient of…

A: When a body is in static equilibrium, the net external force acting on the body is equal to zero. To…

Q: Problem 4. Determine the smallest force P that must be applied to the 150-lb uniform crate to cause…

A:

Q: The 700 N force is applied to 100-kg block as shown in figure, which stationary before the force is…

A:

Q: A B -1 ft- 4 ft +1 ft-

A: We have to find normal force

Q: This climber (mass=52kg) is maintaining this posture while grabbing onto a rock at P3 and reaching…

A:

Q: Q4.A. An effort F is required just to move a certain body of weight 393 N up an inclined plane of…

A: Since you have uploaded two questions and did not specify which question to be solved, as per the…

Q: While digging a small hole prior to planting a tree, a homeowner encounters rocks. If he exerts a…

A:

Q: Q2/ The crate has a weight of W = 350 lb, and the coefficients of static and kinetic friction are us…

A:

Q: Q2/ The uniform 10-kg ladder as shown in Fig. rests against the smooth wall at B, and the end A…

A:

Q: Determine the horizontal force required to push a 2500-lb automobile on level pavement. The auto has…

A:

Q: 3. Car A has a mass of 1.4 Mg with center of gravity at point G as shown in Fig. 3. If car B exert a…

A:

Q: Go -0.3 m-0.2 m+ 0.2 m -0.4 m 0.5 m The hand truck has a mass of 198 kg and a center of mass at G.…

A: In order to solve this issue, we must first compute the net vertical force, the net horizontal…

Q: m = 40 kg 4) Determine the magnitude and direction of the friction force which the vertical wall…

A:

Q: Hello good evening, Permission, i have a question in my homework. The following bellow is question.…

A:

Q: In a hydraulic press, the small cylinder has a diamter of 1 in, while the large piston has a…

A: To Find : The force on the large piston. Given :  The diameter of larger piston is d=8 in. The…

Q: The uniform bar is at rest on a smooth half-sphere with radius R = b / 2. In A there is a ball joint…

A:

Q: The figure shows a bar in equilibrium position resting on the floor at point A and on the wall at…

A:

Q: For steps 4 What happens to the box if there be no force applied? What happens to the box as you…

A: Given question is related to solid mechanics.

Q: Piston ① has a diameter of 0.35 in.; piston ② has a diameter of 1.3 in. In the absence of friction,…

A:

Q: The 180-lb tree surgeon lowers himself with the rope over a horizontal limb of the tree. If the…

A:

Q: 1.0m 3.0m 0.5m mi PA N, 5. The drawing above shows two objects on a board supported at two…

A: Given: m1=40kgm2=20kgm3=10kg…

Q: The crate is being pulled by the man as shown. Given that the coefficient of the horizontal surface…

A:

Q: The 50-kg homogeneous smooth sphere rests on the 30° incline A and bears against the smooth vertical…

A: As per given question  Weight =50kg Angel=30° We have to determine contect of force A and B

Q: A 480-lb lawn roller is to be pulled over a curb with a height of 8 in. as shown. Determine the…

A: Given: The weight of the roller is, W=480 lb. The diameter of the roller is, d=4 ft× 12 in1 ft=48…

Q: 6. Determine the force in each cable needed to support the flowerpot whose weight is 10ON とれ В 6 m 4…

A: The position vector is used to describe the location of a body. When it comes to characterising a…

Q: Wedges A and B are shown in the figure. Assume the coefficient of friction between A and B is 0.2…

A:

Q: Four balls of equal radii form a pyramid supported by a smooth horizontal plane surface. The three…

A: Given there are four balls of equal radius the structure shown is in the form of tetrahedron.…

Q: 2. The man pushes the 120-lb homogeneous crate with the horizontal force, P. Determine the largest…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.