Need help please round answers to 3 sig figs.Thanks Block A has a mass of 30 kg and block B has a mass of 49 kg. The two blocks are stacked on the ramp withan incline of 0 = 33.5°. Determine the largest horizontal force F that can be applied to block B withouteither block moving for each of the following two cases:a.) The friction coefficient for the contact between blocks A and B is 1 = 0.64 and the friction coefficientfor the contact between block A and the ramp is #2 = 0.34.b.) The friction coefficient for the contact between blocks A and B is 1 = 0.64 and the friction coefficientfor the contact between block A and the ramp is #2 = 0.85.ᎾFBACc+❀0BY NC SA2016 Eric DavishahlPart a)The limiting slip condition occurs at Select an answerThe maximum force before either block A or B slips isPart b)The limiting slip condition occurs at Select an answerThe maximum force before either block A or B slips isNN

To findPart (a)The limiting slip condition occurs atThe maximum force before either block A or B…

Block A has a mass of 30 kg and block B has a mass of 49 kg. The two blocks are stacked on the ramp with an incline of 0 = 33.5°. Determine the largest horizontal force F that can be applied to block B without either block moving for each of the following two cases: a.) The friction coefficient for the contact between blocks A and B is 481 = 0.64 and the friction coefficient for the contact between block A and the ramp is μ82 = 0.34. b.) The friction coefficient for the contact between blocks A and B is #1 = 0.64 and the friction coefficient for the contact between block A and the ramp is μ2 = 0.85. F B Cc+❀O BY NC SA 2016 Eric Davishahl

Block A has a mass of 30 kg and block B has a mass of 49 kg. The two blocks are stacked on the ramp with an incline of 0 = 33.5°. Determine the largest horizontal force F that can be applied to block B without either block moving for each of the following two cases: a.) The friction coefficient for the contact between blocks A and B is 481 = 0.64 and the friction coefficient for the contact between block A and the ramp is μ82 = 0.34. b.) The friction coefficient for the contact between blocks A and B is #1 = 0.64 and the friction coefficient for the contact between block A and the ramp is μ2 = 0.85. F B Cc+❀O BY NC SA 2016 Eric Davishahl

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer in15 mints please please please best wishes Ahmed
A Brinell test is performed on a steel using a 1.2 in. diameter indenter with a load of 71825 Ibs. A 0.75 in. Determine in indentation was measured on the surface of the steel. Determine: a) HBN (psi); b) tensile strength (psi) a) HBN = psi b) Tensile strength = psi
Knowing that the vertical component of force acting on a curved surface is given by dFV = PdAx, show that the net vertical force on a sphere submerged at a depth h in a liquid is equal to the buoyancy force on the same sphere.
F P F- b 30 mm 50 30 mm mm Solution workout of this question with proper FBD has to be submitted in MS Teams. Please note down (screenshot) this question. A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.071 m, and the applied force at the handles is F=17.4 N. Choose from the options below (a) the force on the cable, and (b) the force in the member PQ.
Build the following part. Report the mass in pounds. Assume all dimensions are in inches. The material is Vanadium. (Located in the "Other Metals" folder in the material properties.) A = 1.72 B = 1.4 2.40 1.20 T .75 TYP 1.20 TYP .70 -1.00 TYP A A A+3.25 R.35 TYP -R.65 TYP CBORE FOR 5/16 HEX HEAD BOLT Ø.332 THRU ALL LØ813 V 235 .10- SECTION A-A 23. B B+1
26. A JELLO IS sußJECTED TO %3D 0) DRAW THE DEFORMEO SHAPE CALCULATE ?
Hi, Could you please help with this question, if you need to take more credits then please feel free. showing working out if possible too please, Thank you
B P. 200 mm 240 mm 60 30 KN Figure (1.15)
Answer please
‏Generate isometric drawing from multiviews using drawing tools or free - hand . Use approximate proportionate dimensions . Use plane sheet to draw or sketch isometric drawing
Test-II. Write down all the operations or step by step procedure on how to create the object below. Write down also the name of the machines and the tools that you will use to complete the drawing below. 824 020 015 22 15 35 40 100 NOTE: ALL DIMENSIONS ARE IN MM ALL CHAMFERS ARE 1X 45
How would you determine final dimensions using the plus & minus method for question #D??