Biceps muscle. A relaxed biceps muscle requires a force of 25.0 N for an elongation of 3.0 cm; under maximum tension, the same muscle requires a force of 500 N for the same elongation. Find the Young modulus for the muscle tissue under each of these conditions if the muscle can be modeled as a uniform cylinder with an initial length of 0.200 m and a cross-sectional

Biceps muscle. A relaxed biceps muscle requires a force of 25.0 N for an elongation of 3.0 cm; under maximum tension, the same muscle requires a force of 500 N for the same elongation. Find the Young modulus for the muscle tissue under each of these conditions if the muscle can be modeled as a uniform cylinder with an initial length of 0.200 m and a cross-sectional

Related questions

Q: The Young’s modulus for steel is at most 215 GPa (1 GPa= 109 N/m2). If you apply a force of 50.0…

A: Given quantities: Young's modulus of steel (Y) = 215 GPa Applied force (F) = 50 GPa initial length…

Q: A cylindrical steel wire that is 2 m long must stretch no more than 0.25 cm when the applied tensile…

A: The objective of this question is to find the minimum cross-sectional radius of a cylindrical steel…

Q: A steel wire of length 2.08 m with circular cross section must stretch no more than 0.200 cm when a…

A: Given data, Force F=380 N Length L0=2.08 m Young's modulus Y=2×1011 Pa Change in length ∆L=0.2×10-2…

Q: A 18 cm long tendon was found to stretch 5.4 mm by a force of 14.0 N. The tendon was approximately…

Q: The femur bone in a human leg has a minimum effective cross section of 2.85 cm² and an ultimate…

Q: A steel bar is stresses to 250 MPa. The modulus of elasticity is 250 GPa. The bar is 80 mm diameter…

Q: The Young's modulus for aluminium is 7 × 10¹0 Pa. You want an aluminium wire to not stretch more…

A: Given data: Young's modulus (Y) = 7×1010 Pa Stretch in wire (ΔL) = 1.8 cm = 0.018 m Original Length…

Q: A 16.7 cm long tendon is found to stretch 4.22 mm when a force of 15.8 N is applied to it. If the…

Q: A tendon is subjected to tensile forces. The cross-sectional area of the tendon is 0.0002 m2. If the…

A: See below

Q: A marble column with a cross-sectional area of (2.70x10^1) cm² supports a load of (5.500x10^4) N.…

Q: The beam is supported by a pin at A and a short link BC. Figure 0.5m 1 m 4P 1.5 m 4P 1.5 m 0.5m 1 of…

Q: Suppose a person’s femoral diaphysis is idealized as a circular cylinder with a periosteal diameter…

Q: A shaft transmits a moment of force of 1130 Nm. Its allowable stress is 48.3 MPa. Determine the…

Q: A weight of (50kg) affects the lower end of a steel rod of length (80cm) and diameter (0.60cm). What…

A: Given: The mass of the weight is 50 kg. The length of the rod is 80 cm. The diameter of the rod is…

Q: A 15.9 cm long tendon is found to stretch 3.81 mm when a force of 18.0 N is applied to it. If the…

A: The length of the tendon is l = 15.9 cm. The force applied on the tendon is F = 18.0 N. The average…

Q: A spider silk line has a circular cross section. Its diameter is 7.14 micrometers. Its unstretched…

A: When spider changes from the thread, stress will be developed in it , whichbleads yo the expansion…

Q: A wooden "2 x 4" has a cross-sectional area of 38 mm x 89 mm. The shear modulus of the wood is 1.1 x…

A: Given that:

Q: Humans can bite with a force of approximately 795 N. If a human tooth has the Young's modulus of…

A: Young's modulus is defined as the ability of a material to withstand the change in length due to…

Q: Humans can bite with a force of approximately 807 N. If a human tooth has the Young's modulus of…

A: The equation for Young's modulus is given by, Y=σe (1) Here, σ is the stress and e is the strain.…

Q: A sphere of copper has a radius of 8.00 cm and is compressed uniformly by a force of 5.00 × 108 N.…

Q: Assume a human leg contains a 50cm long bone with an average cross section of 3cm. By how much (in…

Q: Humans can bite with a force of approximately 808 N. If a human tooth has the Young's modulus of…

A: Using the equation for Young's Modulus, Y=FLA∆L∆L=FLAY

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

During a tensile strength experiment, a small diameter fibre is elongated by a force of 0.0250 N. The fibre has an initial length of 0.200 m and stretches 4 x 102 m. Determine the diameter of the fibre? The Young's modulus for the material being tested is 7.60 x 1010 Pa.
A man with a mass of 68.3 kg stands on one foot. His femur has a cross-sectional area of 8.00 cm2 and an uncompressed length 50.4 cm. Young’s modulus for compression of the human femur is 9.40 × 109 N/m2. What is the fractional length change of the femur when the person moves from standing on two feet to standing on one foot?
A steel wire, 3.0 m long, has a diameter of 1.0 mm. If a 10 kg load is hung from the wire how far will it stretch? Young's modulus for steel is 2.0 × 10^11 pa
Consider a square-faced beam supporting a section of a building. a) Before installation, the length of the beam is found to be l0 = 15.02 m (figure a). After installation and construction, the length is remeasured and found to be l = 14.98 m (figure b). Determine Young's Modulus Y in N/m2 for the beam if it supports a mass m = 35000 kg and has a side length d = 1.9 m. b) Suppose that after the beam is installed it needs to be repaired. The weight it supports is removed and replaced with a new mass m2 (figure c). After the new mass is supported, the side length is remeasured and found to be larger with a difference of Δd. Assuming that this side length deformation is uniform and small, write an expression for determining Poisson's ratio v for this beam if its Young's modulus Y is known.
The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s = 300, in units of 106 N/m². What are (a) the Young's modulus and (b) the approximate yield strength for this material? Assume & = 0.0010. (a) Number (b) Number 1.5E11 Hint 3E8 eTextbook and Media Stress (10 N/m²) E Strain Units 28 N/m^2 or Pa Units N/m^2 or Pa SUPPORT
A 16.3 cm long tendon is found to stretch 2.11 mm when a force of 18.8 N is applied to it. If the tendon is round and as an average diameter of 5.13 mm, calculate the Young's modulus of this tendon.
The muscle fibers in muscle A have a pinnation angle of 25 degrees, while the muscle fibers in muscle B have a pinnation angle of 20 degrees.Two pennate muscles have the same cross sectional area and produce the same tensile stress. Which muscle can produce a greater amount of force? Muscle B Muscle A Muscle A and B produce the same force