Bf=750 For the shape given, determine the moment of Tf-220 inertia around lines a-a and BI/2-750/2 b-b Hw=930 Tw/2=140/2 Tw=140 B12/2-360/2 T12-130 - B12-360

Q: Determine total indeterminacy and external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+2=5Number of member (m)=8Number of joint…

Q: How to determine Z-value? How to determine D-value and TDT?

A: The Z-value is referred to calculation of the resistance of micro-organism at different temperatures…

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: So there's 3 forces on a body and they're not parallel and they intersect at a point so their angles…

A:

Q: y 130 mm 30 mm 30 mm -40 mm 40 mm-

A:

Q: Is there any simpler way to got AY,AX,BY,BX?

A: This question is related to the Structural analysis from Civil Engineering.

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: For the given structures, determine the degree of indeterminacy. 6. T 6

A: The given beam has three support conditions. The Left end is a Fixed support.(3 reactions)…

Q: A frame ABCDE is subjected to forces Po, Pe, and a moment Mcas shown in the Figure below. If Po = 10…

A:

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: Determine the XT and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: (Figure 1) Express your answer with the appropriate 0 Submit μA 6 a 1₂= 26.268 108 mm Previous…

A:

Q: What does it mean if a beam is “non-compact

A: Beam is defined as a structural horizontal element which is used for resisting loads which are…

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: show the (c)

A:

Q: Problem 12.16 Consider the building frame shown in (Eure) Suppose that My 2.6 k/ft and s8 k/ft.…

A:

Q: (1) a L₁ B P b C L2 C D

A:

Q: For the given structures, determine the degree of indeterminacy. 1. ♫

A: This question is related to the Structure analysis

Q: Classify the structure shown in the figure. OA. Indeterminate. 21st degree O B. Indeterminate, 24th…

A:

Q: y 25 45 55 25 65 80 I 55 165

A: Divide the given area into five parts as shown in part 1 of the question…

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: What are the internal forces at point C of the beam

A: Find reactions:∑ MB=0RA12-500126-900+900=0RA=3000lbFind reactions:∑ Fy=0RA+RB-50012=0RB=3000lb

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: How do I get the support forces

A: The x and y are the vertical and horizontal distances: x=12cos60=6 fty=6sin60=5.196 ft

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: Draw and label theV and M 15KN diagrams. Fill in the blanks. Find M- max and the equations for q. V,…

A: The beam is an important element in the construction of any structure or building. It resists…

Q: sanitary engineering  solve by hardy Cross method  k=8*f*L/pi*g*D^5 f=0.02 g=9.81 pi=e.14

A: Given data in question  Length of pipe  Diameter of pipe Constant value of f Acceleration due to…

Q: Write the full form and define i) CRMB ii) PMB

A: TO Define.  CRMB  PMB

Q: A 2-m-long, cantilevered beam has a 4 kN load applied at its free end and a 2 kN load applied at the…

A:

Q: Find the centroid of X and Y in tabular form.

A: A centroid is a point on the body on which the mass of a body is uniformly distributed. If the body…

Q: Explain why wx = 2/3(9-x)

A: Given:Required:To explain loading intensity for 6<x<9

Q: ified as element.

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: Q1/1/2/ If C(5*5) the counter of the rows isi and the counter of the columns is j,what is the…

A: Assume a square matrix A having  order 3*3 A=a11a12a13b21b22b23c31c32c33i= rowsj=column

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.