Betermine the maximum height of a 3.5' wide by 3.5' long concrete block (y= 150 pcf) with a 2.5' X 2.5' X 3' hollow chamber that will float in the reservoir. Elev. 127.6 Elev. 110 15 Inv. 102.5 Inv. 85 623.5 1000 2000

Q: How many Type of Interior materils.

A: Interior materials : Interior materials are the materials which are used inside the house, like…

Q: How to Install the Gypsm Board.

A: Gypsum Board: Gypsum boards or Plasterboards are one of the latest trends in the construction…

Q: Why is drainage clogging occur?

A: 1)Damaged Pipes-Another major cause of blocked drains is broken pipes. For water to flow freely, it…

Q: Define the Strip loadings ?

A: Strip loads are a common type of foundation load. These types of loads are found on the strip and…

Q: What is Soil Gas?

A: Soil gases:

Q: Define differential hammer,

A: Differential hammers are the same as a double-acting hammer. these hammer having a simpler value…

Q: Define stirrup

A: Stirrup: A stirrup is a closed loop of reinforcement(steel bar) in a beam. It is called as tie-bar…

Q: What are the similarities and difference between the actual ASTM C143 standard and the procedure…

A: In ASTM C143, the test method includes the determination of the hydraulic cement concrete slump in…

Q: Define Bucket augers

A: Unconsolidated Soil: If the soil has not reached the equilibrium under the applied overburden loads,…

Q: Define scour

A: Scour is the removal by hydrodynamic forces of granular bed material in the vicinity of coastal…

Q: Explain pipe earthing

A: Brief concept- Earthing- It is a process by which charge is transferred to the earth with the help…

Q: What is the electrical profiling?

A: The process in which the lateral variation of resistivity in the subsurface is traced to get the…

Q: What is a sieve plate

A:

Q: Define the term Fastener Spacing?

A: Fastener Spacing : Pitch is centre to centre spacing of the fasteners in a row, measured along the…

Q: Define metamorphic.

A: Metamorphic:

Q: How many satellites in a full GPS constellation? O 30 O 12 O24 O 18

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: How are concrete water tanks insulated

A: Insulation of concrete tank is required because loss of moisture can occur as a result of the…

Q: What kind of Fiber Carpet Use.

A: The kind of Fiber Carpet Use are:

Q: Select appropriate sealers for use on exterior applications?

A: Selection of Appropriate Sealer For Exterior surface :  1. A concrete sealer is essential for…

Q: Slab on grade Define.

A: A slab-on-grade is a type of shallow foundation in which a concrete slab rests directly on the…

Q: What is Jet grouting?

A: The jet grouting can be defined as it is a soil stabilization or ground improvement method which…

Q: draw depth of stair landing = 1200 mm  floor to stair landing height = 1500mm

A: Given depth of stair landing = 1200 mm  floor to stair landing height = 1500mm To draw a staircase…

Q: is there any FBD for this?

A: As expert has already solved this question and Student has asked to  draw a Free body diagram for…

Q: What is soil moisture?

A: Soil is a complex material, consists mainly of solid particles, which contains a pores or voids…

Q: A & C are incorrect, please re-work

A: As per question , I solve here only a and c. Find out - (a) Radius of curve  (c) Tangent length

Q: What is Sloped Glazed.

A: Glazing: The installation of glass to the building components or interiors of the structure is…

Q: What are Wet-Impingement Scrubbers?

A: Wet-Impingement Scrubbers:

Q: Q)What are the components of a 3D cement construction printer and a 3D metal printer?

A: The components of a 3D cement construction printer and a 3D metal printer are: 1.Extruders :…

Q: What is Soil stabilization?

A: Soil stabilization is a method of mixing and blending certain materials to improve the properties of…

Q: What is grout?

A: Answer Grout- Grout is the process of injecting the paste of cement, sand, or other chemicals by…

Q: What are the highway culvert design criteria and sizing principles, what risks they are exposed to…

A: Brief concept introduction- Highway culvert- A highway culvert is a drainage system that allows…

Q: How are finished grades determined in machine guidance and control?

A: .Today’s machine-control systems help operators of all skill levels get to finished grade faster by…

Q: Understand installation procedures for carpeting?

A:

Q: hat is volume anaylsis system?

A: Civil engineering is mainly concerned with the planning and detailing of the structure. So for the…

Q: Define Earth pressure loads

A: Pressure is defined as force acting per unit area of the body.

Q: All are incorrect, can you re-work?

A: The degree of the curve = Da = 5°0' The intersection angle = 20°30' The station of the PI = 63+25.53…

Q: Give 7 materials (for walls) Do materials composition and technical specifications only

A: The seven materials for wall construction are 1. wood 2. Concrete 3. Stones 4. Ceramic Tiles 5.…

Q: Describe the term compressibility.

A: Compressibility:- It is defined as the capability of the soil to decrease its volume under…

Q: what method did you use there

A: For forces in member , method of joints have been used and for displacement calculation virtual work…

Q: give detailed information about generalised compressibility chart.

A: It has been asked in the question to give detailed information about generalized compressibility…

Q: why tool coating is important?

A: Introduction This question comes from Engineering tool and safety

Q: Define Core barrels

A: Following is the core barrel definition and uses

Fluid Materials

In general terms, anything that flows can be termed as a fluid. In other words, a fluid is any substance that cannot resist shear forces and deforms continuously under the application of external shear forces. Fluid materials differ completely from solid materials such as metals and alloys. For instance, if we consider two infinitesimally small cross-sectional areas of fluid materials and solid materials, and apply shear forces to these elements, both the elements will undergo deformation. Upon releasing the shear force, the element of the solid materials will regain its original orientation, but the element of the fluid materials will keep on deforming continuously under the action of the shear force.