bent flat bar rotates

Q: Answer The following questions

A: 11. Which type of the following bearing is made up of brass or any other soft material in a round…

Q: It asks what is the width across the flats of the locking bolt head?

A: The width across the flats of the locking bolt head is 0.5625

Q: The __________ square has a moveable inch-graduated blade. Select one: A. SPEED SQUARE B. FRAMING…

A: The combination square has a movable inch graduated blade.

Q: the rim and face alighnment method is a.used only to alighn solid flange couplings b.less accurate…

A: Rim and face method is also called the dial indicator method. it consists of the installment of two…

Q: 13. When tightened, dry seal threads A. are crushed to make a leakproof seal. O B. compress an…

A: According to t the question We need to explain the problem  13,14 and 15

Q: When trying to accommodate only axial loading, which of the following bearings is most likely to be…

A: (a) Tapered roller bearing This type of bearing is used in the places where, vertical and horizontal…

Q: Match each of the following terms to the phrase that describes it. Answers are used only once.

A: The correct match is: Drill spot           -     3Countersink      -     6Knurl                  -…

Q: Hello, I have some diagrams I have filled out for practice that I would like to use to study for an…

A: Diagram 1. E - relief valve A- gear pump D- rotor F- internal gear C- internal and external gear…

Q: Describe the noncircular shafts?

A: The non-circular shafts are ones that do not have a circular profile and the shear stress for the…

Q: I need help with this.

A: Note:We’ll answer the first question since the exact one wasn’tspecified. Please submit a new…

Q: How can we determine the displacement with truss?

A: Virtual work method: This method is a very important method which s used to find the slope as well…

Q: how would you counter boar the hole at the left hand of the shaft?

A: Counter boring is a process in which one end of the existing hole is enlarged. A counterbore tool is…

Q: Describe two types of benders for soft tubing.

A: A metal pipe bender is an important machine tool that provide pipe bends for a vast number of…

Q: Design for 95% male grip force. Use a minimum factory of safety of 2.50. Determine dimensions not…

A: By using the above data and some engineering principles, we can calculate the value of dimension C…

Q: What is the maximum deflection?

A: Given Beam To find Definition of maximum deflection

Q: The largest soft aluminum tubing that may bent by hand is ________________ -inch outside diameter. *

A: Solution:

Q: state 7 types of Engineer’s Hammers as follow:

A: 7 types of Engineer’s Hammers are: Ball peen hammer Sledge hammer: Cross peen hammer: Dead blow…

Q: When facing, the compound rest maybe set 30° (to the cross-slide. If the compound rest is fed in…

A: Draw the diagram of the cross-slide and compound rest.

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.