Before you attempt to plug any saw into a outlet, make sure

Q: How much of the surface beside a weld groove must be cleaned for the AWS SENSE workmanship samples?

A: AWS stands for American Welding Society. SENSE  Schools Excelling through National Skills Standards…

Q: The wiper pads on lathe machine serves the purpose of  Keeping out small chips and dirt between the…

A: To find: the purpose of The wiper pads on lathe machine

Q: which are the main instrucations used in FAPT-TURN? Cutting area definition?

A: The instruction used in FAPT-TURN can be given as,

Q: In Drilling machine, Feed given to drill in this direction makes the hole Select one: a. Downward b.…

A: Given :-  In Drilling machine, Feed given to drill in this direction makes the hole Select one: a.…

Q: It carries the cutting tool and precisely controls its movement either parallel to the ways ,called…

A: Option d is correct.

Q: Describe the Hooke'sLaw?

A: According to Hooke’s law, in the direct loading, stress is directly equivalent to strain within the…

Q: What diameter cutter should be used to create 3/16" radii in the corners of a pocket?

A:

Q: State the OSHA safety procedures of performing oxy/acetylene cutting and other gas cutting process

A:

Q: Which would you use for any of the following situations: Cutting on a smaller mill, a larger mill…

A: Given data: For cutting a smaller mill  A larger mill with little clearance A smaller diameter…

Q: used between slides and slideways are designed to keep out cutting fluids from falling into the…

A:

Q: TOOL USE TO CUT WIRES?

A: Given Wires To find Tool to cut wires

Q: Explain any five safety precautions to be followed while working on lathe machine.

A: Lathes are workshop tools used for performing tasks such as cutting, knurling ,drilling etc. The…

Q: A tool used for making internal threads in G. I. pipes   Pipe Reamer Pipe Vise Pipe Extractor…

A: Galvanized pipe is steel pipe with a zinc coating that prevents the steel from corroding. It's…

Q: A work-holding apparatus that clamps the parts and moves the assemblage to the desired position and…

A:

Q: cutting edge a

A: ANSWER- SIDE CUTTING EDGE ANGLE

Q: Name three different types of pliers

A: Pliers are simple mechanical tool that is basically used to hold bend or pull small objects.

Q: If the chips after metal cutting are too short it is advised to: a/ Decrease the spindle speed…

A: The continuous chips are formed at high spindle speed. (a)  So , to form a continuous chip formation…

Q: Explain in one sentence what "tramming" the toolhead refers to and why it is done.

A: Tram is the squareness of your mill head to the table and "Tramming" is the act of adjusting the…

Q: Advantage of Mechanical chucks is:         a/ High accessibility       b/ Good flexibility       c/…

A: advantages of mechanical chucks are It provides flexibility  in changing workpieces   . It has a…

Q: 11. The twist drill is divided into .. main parts Select one: a.4 b.1 C.3 d.2

A: twist drill has three principles parts: the point, the body and the shank

Q: Main advantage of the Forming taps is:

A: Form taps are ideal for tapping blind holes, but can be used for any tapping application in ductile…

Q: The angle on a single-point cutting tool geometry in which the face of a tool is inclined sideways…

A: Back rake angle: It is the inclination of the face toward or away from the end or the end cutting…

Q: What happens when the boards are bonded together?

A: When the boards are bonded together with an adhesive material, the mechanical interlocking mechanism…

Q: Which of the following works by dragging a bucket towards the machine? Dragline Clamshell O Loader…

A: It is required to determine which machine works by dragging a bucket

Q: What ares name of the tools equipment

A:

Q: Write short notes on points to be considered during maintenance of wiper pad on the lathe machine.

A: points to be considered during maintenance of wiper pad on the lathe machine.

Q: QUESTION 2 1. The operation of enlarging the end of drilled hole to fit an Square bolt is called

A: Boring is an internal turning operation used for enlarging existing holes.

Q: Advantage of Shrink fit chucks is:         a/Easy handling       b/High pull out security…

A: Option b is correct.

Q: .Which of the following are potential safety hazards when operating a lathe? A. Stop the machine…

A: Concept: 1)Potential safety hazards means which is danger to mankind while working on machine…

Q: Precautions when working with a milling machine

A: EXPLANATION :- PRECAUTIONS WHEN WORKING WITH MILLING MACHINE :- 1. Remember to keep all guards are…

Q: __ are cutting processes used to form the edge or surface of wood.

A: ___ are cutting processes used to form the edge or surface of wood.

Q: What is the tool used to hold sheet metal while drilling

A: I

Q: Cold Circular saws are capable of making cuts accurate to what tolerance?

A: Cold circular saws The instrument used in cutting ferrous and non-ferrous alloys material is known…

Q: Which device may be used for either toolholding or workholding?

A: A lathe machine is a machine tool that is used to shape metal or wooden workpieces. In this machine…

Q: Precautions before operating centre lathe

A: The Centre Lathe is a machine which is used to make a cylindrical shapes from a range of materials…

Q: 1. What type of tool is it? 2. What is its main purpose? 3. What secondary functions does the tool…

A: Dear student, we are suppose to solve only 3 sub parts. Please post other parts as a separate…

Q: Main advantage of the Forming taps is:         a/ Evacuates the chips along the shank (for blind…

A: Option b is correct.

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.