Because we will have more data to keep track of for this circuit we will use a couple of data tables to organize our work and our measurements. Table 3-1 will be used to hold our calculated values. Table 3-2 will be used to record our measured values. Use the information from the circuit diagram above to fill in the shaded squares in Table 3-1. These can be considered our "givens" - the information provided for us to work from. Using your Ohm's Law Wheel and Circuit Rules handout you should be able to determine the correct values to fill in for the rest of the open spaces in the data table. Show your work in the space below the table. Circuit 2 Calculated Values Quantity Total Values Resistor 1 (R1) Resistor 2 (R2) Resistance: 4002 2000 Voltage: 120v Current: Table 3-1

Because we will have more data to keep track of for this circuit we will use a couple of data tables to organize our work and our measurements. Table 3-1 will be used to hold our calculated values. Table 3-2 will be used to record our measured values. Use the information from the circuit diagram above to fill in the shaded squares in Table 3-1. These can be considered our "givens" - the information provided for us to work from. Using your Ohm's Law Wheel and Circuit Rules handout you should be able to determine the correct values to fill in for the rest of the open spaces in the data table. Show your work in the space below the table. Circuit 2 Calculated Values Quantity Total Values Resistor 1 (R1) Resistor 2 (R2) Resistance: 4002 2000 Voltage: 120v Current: Table 3-1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Part 1 After using the UT33B multimeter to check the voltage of the batteries and the resistance of, light bulb and resistors, these are the results: - Voltage of the battery is measured to be 1608 mV, The scale used to measure voltage is 2000mV on the UT33B multimeter - Resistance of the bulb is measured to be 0.24 ohm, The scale used to measure resistance is 200 ohm on the UT33B multimeter - Resistance of the resistor1 (R1) is measured to be 15.2 ohm, The scale used to measure resistance is 200 ohm on the UT33B multimeter - Resistance of the resistor2 (R2) is measured to be 27.2 ohm, The scale used to measure resistance is 200 ohm on the UT33B multimeter Part 2 After connecting a circuit to find the resistance of the light bulb and resistors experimentally using a circuit, these are the results: LIGHT BULB - Resistance of the light bulb and resistors could not be measured on the UT33B multimeter, so the voltage and current were measured and the resistance was found using ohms law.…
In the figure R₁-3.41R, the ammeter resistance is zero, and the battery is ideal. What multiple of e/R gives the current in the ammeter? EH Number Units *E/R
Which of the following statements is true ? OA. Power is additive in series and parallel circuits. O B. A battery is a current source. OC. In a closed circuit, current leaves the positive terminal of a battery, and is used up by the time it reaches the negative terminal. O D. Current only flows through the path of least resistance.
In the circuit, Determine: a. the total resistance (R7) of the circuit in kl. (. . places for the final answer) b. the current flowing in mA for each of the resistors, R1, R2, R3 and R4 ( use 2 decimal places for the 12V final answer) c. the voltage in V across each of the resistors, R1, R2, R3 and R4 ( use 2 decimal places for the ; use 2 decimal R = 3000 R3 = 4000 R2 = 1000 R4 = 1ka %3! final answer)
voltage across R has to be measured with a voltmeter. What percentage error is expected in measuring the voltage if R₁=R₂=R3=R₂=R-100 Q for meter resistance of 1500 Q and 15000 Q. Also calculate the percentage error in measuring the current through R, if the ammeter resistance is 15 and 1.5 Q. Assume Eo, lo as true value and Em, Im as measured value. 10: F 20 20 I' R₁ R₂ R3 ARA A Rg J B 1500022 ģiseen 15000
Consider the circuit in the given figure. Assume R1 = 120 S and R2 = 260 N. R R2 40 V Calculate current i in the given figure when the switch is in position 1. The current when the switch is in position 1 is mA.
Question: The current in the 8.00 ohm resistor below is 0.84 A a.) Find the current in the 20-ohm resistor and in the 9-ohm resistor. b.) Find the equivalent resistance across the circuit.
State the characteristics of voltage and current in a series circuit connection of resistors. State the characteristics of voltage and current in a parallel circuit connection of resistors. please explain it properly.
answer it theortical as it asked