bearings. : Convert the following quadrantal bearings into whole circle (a) (b) (c) (d) (e) (f) N 30° 15' E S 40° 30' W S 20° 30' E N 30° 30' W N 20° 0' E N 20° 0' W

Q: Tmax 19 (Ox, Txy) 0₁ ON 0₂+Oy 0,20 2 (0₂₁ Tyx) ₁ and 2 are 64 and -9 respectively. Locate the centre…

A:

Q: I. True or False. Write TRUE if the statement is correct and FALSE if the statement is incorrect. 1.…

A: Given statements:1. Stress is pressure exerted on a material object; it may have a unit of kN.2.…

Q: find the stresses on the plane 45 Draw

A:

Q: PROBLEM 01 REFER TO FIGURE 01, DETERMINE THE INTERNAL FORCES ACTING ON THE FOLLOWING MEMBERS: (STATE…

A:

Q: Complete the following differential level notes for a double-rodded line from BM1 to BM2. Show the…

A: Complete the following differential level notes

Q: Find end moment slope de fiction use 100kN

A: We have 5 members in this figure. 4 fixed support. The load is acting on a mid span of AC This is a…

Q: A straight steel bar is fastened to a gusset plate with three 3/4-in diameter ASTM A-307 bolts, as…

A: three 3/4-in diameter ASTM A-307 boltsbolt capacity in single shear  = 7.95 kips plate capacity =…

Q: 5- y = logs sech(5x)

A:

Q: 25° 50° C. A 51

A: Consider the force diagram of the system shown below. The x component of the resultant force is…

Q: Find the load carried by crane F and boom angle 43 degree and crane weight 800KN 5M 6M Gc 2.8 m F…

A: The forces in the crane and the mass of the object are finding from the equilibrium equations of the…

Q: Question / Find Ax at Joint C, and O, by using Virtual Work Method, if you know E = 200 GPa, I =…

A:

Q: In Compass traversing length of lines are measured by O a. Dumpy level O b. Theodolite O c. Chain O…

A:

Q: 15. A bridge 100 m long is to be built to span a valley as shown. From point A, the angle of…

A:

Q: Convert the following Reduced Bearings into WCB. • N 65° E • 439 15' E S 52º 33' W •N 32º 42' W

A:

Q: Calculate the min. External dia of shaft.

A: Power transmitted by hollow shaft at 1200 pm = 450 Kw Allowable shearing stress in the shaft = 60…

Q: Student Portal : FEU.. EG8245H5 Das Google M Inbox (258) - 20191... Mga Klase ? Student Login…

A:

Q: block of 50 kg is attached to a cable. The cable is then attached to a rotating assembly with mass…

A: concept- Work will be negative as friction is CCW and displacement is in CW

Q: An existing vertical curve on a highway joins a +4.8% grade with a -4.8% grade. If the length of the…

A:

Q: Compute the magnetic bearings of sides AB,BC, CD, DE AND AE.

A: Solution:- The given diagram is shown below,

Q: com/webapps/assessment/take/take.jsp?course_assessment_id=…

A: Using formula to find angle of twist

Q: Q2 All members of the truss in Figure Q2 are to be fabricated from the same stock of thin-walled,…

A:

Q: RI 038 R32 80

A: For the given figure, i had drawned in AUTO-CAD using the following commands 1. CIRCLE COMMAND 2.…

Q: Determine the horizontal distance from O of the shear centre of the thin-walled beam section shown…

A:

Q: 4. Use the component method to determine the component of each force along x and y axes. F1 = 494 lb…

A: Introduction- The given values are shown below, F1=494lbϕ=58.2° We have to find the component of…

Q: Q3/ The square gate is 3 m wide normal to the plane of the diagram as shown in Figure * .is hinged…

A: Given H=1.5m Wide normal=3m Theta=30degrees

Q: Replace the loading by an equivalent resultant force and determine where its line of action…

A: Equilibrium of horizontal forces, ∑Fx=FxFx=250cosθ-300-500cos30°=25045-300-5000.866=-533 N The…

Q: Please solve manually

A: The image shows a complex engineering problem for a hollow steel beam (HSS) structure. I can't solve…

Q: The two forces acting on the handles of the pipe wrenches constitute a couple 'M'. Express the…

A:

Control Survey and Geodetic reductions

Control surveys or survey controls are used to establish reference points as a basis for various construction activities. Vertical and horizontal control points are to be established in a control survey to increase accuracy. After establishing the control points, all other types of surveys such as topographic, right-of-way, aerial mapping, construction layout, boundary surveys, and utility mapping can be worked upon so that control networks can be formed. The place from which the observations are made is called a survey station.