Beam ABCD is simply supported at B and C and has overhangs at each end (see Fig, a). The span length is L and each overhang has length L/3. A uniform load of intensity q acts along the entire length of the beam.a. Draw the shear-force and bending-moment diagrams for this beam.Repeat part (a) if the uniform load is replaced with a triangularly distributed load with peak intensity q0= q at mid-span (see Fig. b).

Q: Cantilever prismatic beam is loaded by concentrated loads.

A:

Q: 1- The simply supported beam in figure below has a rectangular cross section 120 mm wide and 200 mm…

A:

Q: 10 kips 3 kips/ft A 3 ft 4 ft 3 ft Draw the moment diagram by parts in your solution sheet. Assume…

A:

Q: A ec=K L B b→,K 1. (Section)

A:

Q: Question 1) F=16 kN single load, M=22 kN.m moment and w=11 kN/m distributed load are acting on the…

A: As per the guidelines we will answer the first three subparts for you. for the rest of the subparts…

Q: The shape of the beam made of U profile ensures safe loading. Find the length c of the overhangs so…

A:

Q: Q4: A simply supported I-beam of (2 m) span carries a central load of (4 kN). The load acts through…

A: Given Datal=2mP=4kNθ=30°

Q: Pravinbhai

A: The objective of the question is to determine the principal stresses and the maximum shear stress…

Q: Question 1) F=35 kN single load, M=45 kN.m moment and w=16 kN/m distributed load are acting on the…

A: A pin support will exert both horizontal and vertical components of reaction. The support A is pin…

Q: A beam of 8 m long, loaded with uniformly distributed load on the 4 m span CE with a concentrated…

A: The free body diagram of the beam is as follows: Calculate the moment about point d as follows:…

Q: The extended beam ABC in the figure below is pin-supported at A and roller-supported at B. For the…

A:

Q: Consider the beam shown in the figure. The allowable tensile and compressive of a beam material are…

A:

Q: F=16 kN single load, M=22 kN.m moment and w=11 kN/m distributed load are acting on the beam whose…

A: Given data, The inclined applied force, F = 16000 N The applied moment, M = 22000 Nm The applied…

Q: igid support geomet in the figure and parameter table. Find the equations for the shear and moment…

A: Given: The length of AB, L1 = 4 m The length of BC, L2 = 4 m The length of CD, L3 = 3 m The moment…

Q: In the figure, find the length c of the overhangs so that the beam made of U profile can carry the…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: Use Castigliano's theorem to compute vertical and horizontal displacements at the point of…

A: Given data,

Q: F W 50 mm 20 mm -2 m

A: Free body diagram of the beam:

Q: Maximum bending moment: A simply supported rectangular beam that is 3000 mm long supports a point…

A: Write the given data. P=5000 NL=3000 mmb=127 mmh=254 mmd=254 mm

Q: A simply supported beam of length L = 1 m (A = hinged support, B = Roller support) is shown above…

A: Given data :- L = 1 m                         a = 0.4 m                         P = 1.7 kN (A) By…

Q: 2. For the 20 meter beam shown, there is a roller at "A" (Ay = 52 kN; it is acting upward), and a…

A: For the 20 meter beam shown, there is a roller at "A" (Ay= 52 KN; it is acting upward), and a pin…

Q: The simply supported beam carries a uniformly distributed load over parts of its length. Compute (a)…

A:

Q: 1) For the beam in the figure, determine the expressions for the distribution of internal shear…

A:

Q: The specifications of the inverted T section of a 4-m simply supported beam are illustrated in the…

A:

Q: Compute the reaction forces at support A and B in terms of w0, with the aid of free body diagram.

A:

Q: A beam of 8 m long, loaded with uniformly distributed load on the 4 m span CE with a concentrated…

A: Given dataSN = Student NumberTotal length fo the beam L = 8mBending moment = SN (kN)To draw the…

Q: Sketch the free body diagram of the beam, with appropriate labelling (Y value is 7)

A:

Q: The simply supported beam supports a uniformly distributed load of w=240 lb/ft between supports A…

A: Given:To find:Principal stresses and maximum shear stress at point K.

Q: d () The maximum bending moment, (ii)Bending stress induced, (i) Radius of curva ake E as 100 GPa.…

A: Givensimply supported beam length L=3muniformly distributed load w=26kN/m entire spanrectangular…

Q: Consider the beam shown. Suppose that M= 9 kip*ft, P=8 Kip,w=1.4 kip/ft and point D is located just…

A:

Q: In the figure, find the length c of the overhangs so that the beam made of U profile can carry the…

A:

Q: F=20 kN single load, M=21 kN.m moment and w=20 kN/m distributed load act on the beam whose loading…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts for…

Q: Q1/ A beam (ABC) is supported at A&B and carries a uniformly distributed loads between AB of 60N/m…

A: Here we will apply the equilibrium conditions

Q: 2) 5.5-5 A rectangular beam ABC (L = 15 ft; h= 12 in.) has simple supports at A and B and an…

A:

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.