Based on the figure given, determine the removal efficiency of the settling column if the overflow rate is 0.012m/min.240 270 300 ti )Q Zoom65 - 74%55 - 64%75 - 84%85 - 94% Depth, m0.0100%90%1.050%60%2.080%70%3.0306090120150180210240270300time (min)

GIVEN OVER FLOW RATE SO ACORDING TO THAT PLOT A GRAPH

Answered: Based on the figure given, determine…

Engineering

Civil Engineering

Based on the figure given, determine the removal efficiency of the settling column if the overflow rate is 0.012 m/min.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the diameter of a settling tank required to remove particles from a depth of 2.4 m when…

A: Given: Depth, H = 2.4 m Overflow rate = 15 m/day Discharge, Q = 900 m3/day

Q: A settling basin is designed based on a surface overflow rate that can achieve a removal efficiency…

Q: A conventional rectangular clarifier is to be used to remove lime precipitates following softening…

A: A clarifier is a tank used in waste water treatment plant to remove solid particles from liquid…

Q: the required backwash velocity is

A: Given data: Determine the required backwash velocity? Where, data as follows: diameter,d= 0.4 mm…

Q: A water filtration unit is made of uniform-size sand particles of 0.4 mm diameter with shape factor…

Q: settling basin is designed based on a surface overflow rate that can achieve a removal efficiency of…

A: d1=0.05mm d2=0.1mm

Q: A pumping well was drilled penetrating straight into an unconfined aquifer with the thickness of 42…

Q: The town of Parit Raja has an existing horizontal-flow sedimentation tank with an overflow rate of…

A: Finding out percentage of particles removable.

Q: 1. You are to design four sedimentation basins which operate in parallel. The total flow influent,…

A: Q- 24 MGD B- 30 ft L- 240 ft d- 10 ft μ= 2.73 ×10-5 lb/sec/ft2 T=50° ν= 1.41×10-5 ft2/sec s=1.6 To…

Q: Suspended particles at a depth of 3 m are to be removed from water flowing at the rate of 250…

A: Given: Depth, H = 3 m Flow rate, Q = 250 m3/day Overflow rate of tank, Qo = 20 m/day

Q: A 0.80 m deep bed of sand filter (length 4m and width 3m) is made of uniform particles (diameter =…

A: Given- Length L=4 mWidth B=3 mDischarge Q=3.6 m3/minDepth of bed D=0.8 mBed porosity n=0.4 It is…

Q: 3-A circular radial-flow tank has a settling zone depth of 3 m and a settling zone area of 500 m2.…

A: Given: The depth of the settling zone is 3 m. The area of the settling zone is 500 m2. The settling…

Q: SITUATION 3- GREEN- AMPT INFILTRATION METHOD A soil somewhere in Pangasinan has the following…

A: Given that Ks=1.5in/hr , i= 8.2in/hr From the green ampt infiltration method

Q: falling head permeability test was run on a soil sample 12.4 cm. in diameter and 14.9 cm. long. The…

Q: d. Round off to four decimal places.

Q: A water filtration unit is made of uniform-size sand particles of 0.4 mm diameter with a shape…

Q: Question A water filtration unit is made of uniform-size sand particles of 0.4 mm diameter with a…

A: Given- Terminal settling velocity Vs=4.5 cm/s, Porosity n=0.65, G=2.55 It is needed to find the back…

Q: For the following soil properties determine the volume of infiltration at surface saturation (Fs)…

A: Given that ks=1.75 in/hrθs=0.315θi=0.212ψ=-9.15 ini=7.75 in/hr We know that…

Q: For the particle-settling data shown in Question 9, plot the removal efficiency as function of…

A: Answer We are given Fluid velocity Vf =0.5 cm/s = 0.005 m/s dimension a = 72 m dimension c = 3.5 m…

Q: A sedimentation tank is to treat a water flow of 85,000 m3/d having a kinematic viscosity of 9.5 x…

A: Given data in question Flow rate Kinematic viscosity Diameter of particles Specific gravity To…

Q: 12. (Horton's equation for infiltration rate, ). One can use Horton's equation to estimate the…

A: Given:To find:

Q: A detention pond is designed to achieve 100% removal of 0.1 mm fine sand particles at the design…

A: Since a detention pond is designed to achieve 100% removal of 0.1 mm fine sand particles at the…

Q: A silt particle with a density of 2500 kg/m3 and terminal settling velocity (vs) of 1.9 m/hr is…

A: The given data is shown below:

Q: DISCUSS AND ELABORATE WHAT IS THE BEST METHOD ESTIMATING EVAPORATION?

A: Solution: Evaporation is the process by which liquid water evaporates into the atmosphere,…

Q: 3.4 m 0.8 m + 3.2m 4.2 m T 6.0 m と seepage

Q: A soil has the following soil properties for use in the Green-Ampt equation: n = 0.464 K = 1.5 in/hr…

Q: A 3 m deep settling tank has a surface area of 900 m?. The tank is used for removing particles of…

A: Given: Depth of tank, H = 3 m Surface area, A = 900 m2 Particle size, d = 0.01 mm Specific gravity…

Q: settling tank has an overflow rate of 100,000 gal/ft^2 •d. Water carrying sediment of various sizes…

A: Overflow rate = 100,000 gal/ft2settling velocitymass friction…

Q: Sedimentation is the process of allowing particles in suspension in water to settle out of the…

A: Given: Discharge for four clarifiersQ=1.5 MGD Q=1.5×3785.4 m3day 1 MGD=3785.4 m3day Q=5678.10…

Q: Use the Green-Ampt method to evaluate the infiltration rate and cumulative infiltration depth for…

Q: A slurry flowing at a rate of 8000 m3 /d is fed to a rectangular sedimentation tank to separate the…

Q: For a rainfall intensity of 1.94 cm/hr, a ponding time of 10 minutes was observed or a soil with 40%…

A: There are many ways to define soil. An unconsolidated mineral stratum is a natural mineral…

Q: A gravity rapid sand filter with an effective size of 0.55 ent is 1.2 designed for a water treatment…

A: The given data in the question is: The gravity rapid sand filter has an effective size of 0.55 mm…

Concept explainers

Principles of Seepage

In hydrology, when water flows down in a pore or crack of unsaturated soil due to gravity, the deep layer of soil is called seepage. It is the slow movement of water in the soil layer. Seepage is mainly found near hydraulic structures and is responsible for the stability of earthen-type hydraulic structures.

Question

Based on the figure given, determine the removal efficiency of the settling column if the overflow rate is 0.012
m/min.
240 270 300 ti )
Q Zoom
65 - 74%
55 - 64%
75 - 84%
85 - 94%

Depth, m
0.0
100%
90%
1.0
50%
60%
2.0
80%
70%
3.0
30
60
90
120
150
180
210
240
270
300
time (min)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem No. 3 A sedimentation tank with 600 m surface area is designed to treat 1100 m'/day of water with influent suspended solid of 150 mg/l. Determine the effluent suspended solids, Due to population increase, the quantity of water increased to 2500 m'/day and it is intended to install another sedimentation tank in parallel with the existing one, determine the surface area of the second tank. The mass fraction remains and corresponding settling velocities of water sample is illustrated in the following table: percent 100 70 50 30 15 Vx 10 m/min 3.0 2.0 1.5 1.0 0.5
A rectangular sedimentation basin with a length twice the width and 3 m deep, receives a flow of 2400 m/day with a normal concentration of suspended solids of 120 mg/l Determine: 1. The surface over flow rate (SOR) when the detention time is 6 hours. 2 The water entering velocity to the basin (cm/min) 3. The efficiency of the basin when the total mass of sludge produced per day is 216 kg.
3. Using the settling curve provided and given information, a) Determine the solids loading in kg/m²/d. b) Calculate the overflow rate in m³/m²/d. c) Find the thickener surface area required in m². d) Determine the settling velocity of the particles (Ah/t). Assume that initial concentration is 1,500 mg/L, thickened concentration is 10,000 mg/L and flow of 2,500 m³/d. Interface height (m) 0.7 0.65 0.6 Settling Curve 0.55 0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 0 10 20 20 30 40 Time (min) 50 50 8. 60 70 88 80
A rectangular settling tank is to treat 3.6MLD of raw water. The sedimentation period is to be 3 hours; the velocity of flow is 10 cm/min. The cross sectional area of the basin (in m², round off to the nearest integer) is
Results of an infiltrometer test on a soil are given below. Determine the Horton's infiltration capacity equation for this soil by identifying the parameters fo fcand k. Time from start (hr) 0.25 0.50 0.75 1.00 1.25 1.50 1.75 | 2.0 Infiltration capacity in cm/hr 5.6 3.20 | 2.10 | 1.50 1.20 | 1.10 1.0 1.0
Determine the minimum dimension of a particle that can be completely removed from a settling chamber, if the rate of overflow is 30 m3/d/m2. Take specific gravity of particle equal to 2.65 and the dynamic viscosity equal to 1 x 10-5 Ns /m2.
Question 2: After conduct an experiment, you found that the soil for the watershed have an initial rate of infiltration equal to 1.35 in./hr and a final capacity of 0.3 in./hr. Assuming that the time constant k = 0.4, calculate the soil infiltration capacity at the times 10 min, 15 min, 30 min, 1 hr, 2 hr, 4 hr, and 6 hr using Horton's equation. Infiltration
A settling tank having a depth of 3.5 m and surface area of 1000 m2 is used to remove particles of size 0.01 mm and specific gravity of 2.7. Calculate the removal percentage of the tank for a discharge of 7000 m3/d. Take viscosity of water as 10-3 kg/m.s.