Based on the circuit of Figure 2(b), design an inverting amplifier d) that has a gain of -35 with the output offset voltage minimised. Given R, = 2OL, determine the values of the resistors, R, and Re. Note that L is the last digit of your student number. For example, if your number is C1700123, then R, = 203 kn, or if your number is C1700100, R, = 200 kn

Based on the circuit of Figure 2(b), design an inverting amplifier d) that has a gain of -35 with the output offset voltage minimised. Given R, = 2OL, determine the values of the resistors, R, and Re. Note that L is the last digit of your student number. For example, if your number is C1700123, then R, = 203 kn, or if your number is C1700100, R, = 200 kn

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A supercapacitor is an electrical energy storage device. A supercapacitor, initially charged to 9.8 thousand millivolts, supplies power to an emergency beacon. The power draw from the load causes the capacitor to lose 4.4% of its charge every minute. When the charge drops below 7 hundred millivolts the beacon will cease functioning. How long will the beacon last after it is activated (your final answer should be in minutes). Round your answer to the nearest minute.
Draw the osciloprams for ult) ond ick] Problem For the following pairs of voltages and currents, indicate whether the element involved is a capacitor, an inductor, or a resistor, and the value of C, L or R if sufficient data are given: u = 550 sin( 377t + 50°) i= 11 sin( 377t - 40°) a) u = 36 sin( 754t +80°) i= 4 sin( 754t+170°) b)
Microprocessor
Give solution/explanation for letter i only. Answer Capacitive, 8.4883?FSubquestion/s are given with their corresponding answers. A pure element is connected across an AC signal. CH1 and CH2 measures the voltage and current respectively:CH1 (Yellow) SettingsVolts/Div: 50VTime/Div: 5msProbe Settings: X1CH2 (Blue) SettingsCurrent Probe Ratio: 100 mV/mAVolts/Div: 20VTime/Div: 5msProbe Settings: X1If ?? (distance between two ‘purple’ cursors) is 5ms, determine:a. Periodb. Frequencyc. Phase Angle Differenced. CH1 Peak Voltagee. CH1 RMS Voltagef. CH2 Peak Currentg. CH2 RMS Currenth. Impedance of the pure elementi. Type of load. If reactive, indicate the values of inductance or capacitance a. 20 msb. 50 Hzc. 90°d. 150 Ve. 106.066 Vf. 400 mAg. 282.8437 mAh. 375 Ωi. Capacitive, 8.4883?
Calculate the R value in ohms, since the 13kHz frequency sinusoidal sign is observed at the output of the circuit in the picture. (C=10nF)
(1) S sin3x sin2x dx
Calculate Theoretical Impedance by formula Z
7) In the circuit below V A-B = 48.3 /30° What is the value of V1?
Determine the energy stored (in units of mJ) by Ca when C, = 20 µF, C2 = 10 µF, C3 = 14 µF, C4 = 30 µF, and Vo = 73.4 V. C, Select one: OA. 5.75 OB. 1.35 OC. 0.78 OD. 84.05 OE. 8.62
Find the trasfer functon Cin hap lace tran Sformi) for the following system
Electrical Engineering +12V R8 R9 R1 8,2K R2 4,7K R6 1000 1502 22K T3 LED3 RED ВС558 LED1 8 BLUE LED4 RED R3 10K LED2 R7 33K LED5 RED BLUE IC1 6 NE555 IC2 3 NE555 3 T2 BC548 R10 6 1000 2 T1 L14F1 LED6 +L C1 220u R4 1002 R5 4702 C3 2.2p 25V A LED7 WHITE C2 0.01u C4 25V "0.01p LED8 GND draw the circuit in block diagram preparation. like this 2.1 Block Diagram of the circuit Relay circuit Load Relay driver circuit LDR switch circuit AC Bridge Rectifier Voltgae Regulator Oscilator circuit Logic Circuit Transformer supply Swihch ing Icircuit ww www wi www
9. The value of Inductance can be determined by a. 2πf / X b. X / 2πf c. X / 2π d. X 2πf