Based on the circuit configuration, determine the following: a) Ceq b) q1 c) V1 d) Vs จ C1=5&F se C4 = 8 MF He C2 = 10F He C5 = 8/F HE C3 = 6F Ht 400- V+ = 12v

Q: Q14: The arithmetic shifts right instruction ashr means divide the number by 2. Find the result of…

A: First 08 is loaded into the Acummulator in the form of binary. Given that ashr means divide the…

Q: How many digits is the Octal System capable of having?

A:

Q: (3 decimal final answer please with clear solution!)  If Iab is equal to 292.717∠52 and Ib is…

A:

Q: BCD Addition: 7598+ 489=

A:

Q: Table 1-4 4-Bit Reflected Code Reflected code 0000 0001 0011 0010 0110 0111 0101 0100 1100 1101 1111…

A: The other two codes we ca use are Hexadecimal code Binary code

Q: What is the maximum number of digits that may be used in the Octal System?

A:

Q: Determine the following: Ic, VF , VR , R1

A: BJT (bipolar junction transistor) A transistor having a three terminal made up of semiconductor…

Q: Which of the following statements about printed circuit boards is correct? O a. It can be single,…

A: PCBs are called as printed circuit boards. They are used as support for electrical and electronic…

Q: What is the maximum number of digits that may be used in the Octal System

A: We need to find out the number of digits in octal system .

Q: How many digits is the Octal System capable of having?

A: Numbers can be represented using various number system. Four basic number systems are - Decimal…

Q: Could someone explain the solution picture 1 with the 'OR'. The solution is on picture 2 but I want…

A: According to the question, for the given circuit as shown below We need to explain the problem…

Q: In HDB3, If the number of non-zero pulses is even, the format used is a. V000 b. B00V c. V00B d.…

A: The HDR-3 is HIgh Density Bipolar 3 Zero Coding.It is more conservative than other coding methods

Q: what was the calculation done to get d? Confused on how this was rearranged.

A:

Q: The number of possible values for signals is restricted. a. Analog b. Digital c. Either (a) or (b)…

A: A digital signal is a signal which is represented as s sequence of discrete values.  In digital…

Q: Add these hex numbers by converting each symbol to decimal and then converting the answers back to…

A: Addition and conversion to Hex

Q: Write an Arduino code to control two LEDs using two push buttons, given the bellow setup: LED 1 is…

A: The LED pins should be used as output pins and Button pins should be used as Input pin in program.

Q: How must the uno be configured to create a traffic light? A. Pins can be configured any way B. 1 pin…

A: Arduino Uno :  The Arduino Uno is a microcontroller board based on ATmega32u4.

Q: I need the answer as soon as possible

A: DRAM read Operation- It is basically known as Dynamic Ram" (DRAM)  In DRAM, it needs to refresh for…

Q: This doesn't match the answer on the answer key I submitted with it - I was hoping to know the…

A: The required parameters can be calculated by using the equivalent impedance of capacitor and…

Q: Suppose there are 6 digits [0,1,2,3,4,5], please tell me there are how many combinations for…

A: Given, The 6- digits are [0,1,2,3,4,5] Number of combinations of a 3-digit number with distinct…

Q: Count Mounting method 15. From the information you have studied about the various electrical…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Crystal radio receiver Please explain how this circuit works

A: NOTE- According to the policy, we can answer only one question, please post other question as…

Q: V battery. Calculate the current heir resistance. Assume that th

A: Given as, Ice mass, m = 0.1 kg Voltage of battery , V = 24 V

Q: Explain how the IGBT switch works. Draw the symbol and its characteristic curve.

A: The IGBT is a power switching transistor having advantages of MOSFETs and BJTs for use in power…

Q: Which of the following is a 'marking'/measuring tool? B. Inside caliper D. Hand file A. Hack saw C.…

A: INSIDE CALIPER:  an instrument used to measure inside dimensions HAND FILE: usually a hand saw with…

Q: 3. Determine Vo. 12V(+ 82 W Vo 252 W 7V

A: Given: A circuit with series resistor and two series batteries. To find: Voltage V0.

Q: Choose the best expectation for the value of Output for the codes below if the NO pushbutton noPB is…

A: IN1=80 IN2=3 IN3= 3 IN4= 6 Expression OUT=IN1/(IN2-IN3)+IN4

Q: For the following circuit, write a code on TinkerCAD to turn on the LED light when the push-button…

A: Given the circuit, as shown below: For the following circuit, we need to write a code on TinkerCAD…

Q: Fill in the Blank: A is a Punch Down Block which has 25 rows of four metal pins.

A: The 66 block is the punch down block that is used for connecting the wire a telephone line system.…

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.