B6

Q: R20

A:

Q: Determine the number of divisions required on the vernier scale, if it is combined with the main…

A: given- least count of main scale=0.5 mmleast count of combination of direct vernier=0.05 mm

Q: B 7m |C A 5m 6m 8m

A: Given: A tank filled with lubricant oil exerting 150 kPa Required: To find vertical stress increase…

Q: E A F D 3 in. in. G -2 in. 1.5 in B

A:

Q: Compute the total length of 10 mm diameter stirrups for a beam section 500 mm x 250 mm. Total length…

A:

Q: Determine the coordinates of the centroid for the shaded area

A:

Q: Calculate coordinate of centroid for a parabolic segment OAB which is +² bounded by the x-axis and…

A:

Q: 100 mm 150 mm

A:

Q: For the section shown below verify the following equations (7) Z section th'b' (b+h 12 (26+h B D C

A: Consider the given figure So here we have to verify J=t332b+hI12=th2b312b+h2b+h

Q: determine the centroidal axis xx of the section shown in the figure

A: The given section can be break into two rectangles, Let the unit of all dimensions are in mm,

Q: QUESTION 5 Which of the following represents the location of the horizontal plastic neutral axis (X,…

A: Solution Find the location of horizontal plastic neutral axis

Q: Determine: a) Differential Area b)  Centroid distance along x and y axis   *use 3 decimal places…

A:

Q: determine the distances x and y for equilibrium if f1=800 N and f2=1000N. (Hand written and clean…

A: Given data - F1 = 800 NF2 = 1000 N Find out - Distance x and y ?

Q: Find the centroid, ^y, and moment of inertia Ixx of the following sections.

A: The moment of inertia about X-Xaxis can be found using parallel axis theorem, IXX=IGG+A×h2IGG=MOI…

Q: p² – 3r + 2 lim r-1 r - 1

A:

Q: DRAW THE SECTION INDICATED BY THE CUTTIN

A: Any view obtained by a projection on a plane other than the horizontal, frontal, and profile…

Q: can u get the

A:

Q: 1" 5" 2" 1-Determine the location of the centroid (x,y) of the centroid. 2- Determine the Ix0 and…

A:

Q: Define deflection angles.

A: A deflection angle is an angle between the onward extension of the previous leg and the line ahead.…

Q: Why Nc=9 and Nq=1

A: Given question is based on static method of analysis bearing capacity of pile.

Q: 1) Compute the coordinates of the area centroid with respect to the given axes. 2m im 2m--- Zm- Im

A: To find centroid of given figure

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: What does it mean if a beam is “non-compact

A: Beam is defined as a structural horizontal element which is used for resisting loads which are…

Q: 1. Find the shortest path from A to D. B 2 3. 2 G 5 F8E

A:

Q: Determine how far is the centroid of the given cross section above the base. 6-504 2-50" 9.0" 6.5"…

A:

Q: PROBLEM 1 Determine the x- and y-coordinates of the centroid of the shaded area. y 0 0 ♡ 100 y = 1+1…

A:

Q: Breaks the selected object .between two points You can create arc or line between two specified…

A: Given- Breaks the selected object .between two points   a) You can create arc or line between two…

Q: Lim x25X+ 2 2X+ 2X-1 .3 メ→。

A: To evaluate: limx→∞x2-5x+22x3+2x-1

Q: PROBLEM 2 The centroid of the T-section shown is 2.5 inches above the base. What should be the value…

A:

Q: D A E Given side B G Assuming that all stations are occupied and al lines are observed, what is the…

A:

Q: CORRECT ANSWER

A:

Q: 4x-2x2+1 find lim, 3x-5

A:

Q: y 25 45 55 25 65 80 I 55 165

A: Divide the given area into five parts as shown in part 1 of the question…

Q: ] Use graph paper to draw simplified sketch of the gear and the rack shown in problem 5/64(79). What…

A: Figure is as shown

Q: Determine the importance of utilizing an S-Curve in the field of Construction. Own words and atleast…

A: S Curve in construction: S-Curve is a chart or graph showing construction cash flows over a project…

Q: Find shape factor Q about the y-axis.

A:

Q: 11. Which IS codes gives details about elevators? A. O IS 27752 B. O IS 38665 C. O IS 14665 D. O IS…

A: IS code that gives details about elevators

Q: Calculate Q for a W10x15 cross section (A992).

A:

Q: Describe about the tangent modulus.

A: Tangent modulus:- The instantaneous rate of change of stress as a function of strain. The slope of…

Q: *9-64. Locate the centroid (, y) of the shaded area. y 1 in. 3 in 3 in. 3 in. Prob. 9-64 Ai=…

A:

Q: Xxccj

A: Xxccj - these are the word of the english language

Q: Which among the following determines the direction of closing error? a. Tan δ = ΣD/Σ O_b. c. d. Tan…

A:

Q: Determine the horizontal distance from O of the shear centre of the thin-walled beam section shown…

A:

Q: Halp me to out

A:

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.