B10 q10.2 A 100 cm wire is used in a potentiometer circuit to determine the Es = 6 V unknown emf's of two batteries E1 and E2. When the first battery El is connected the balancing length I is found to be 50 cm and when the battery E2 is connected the balancing length l is 20 cm. For this case the following statement is accord:

B10 q10.2 A 100 cm wire is used in a potentiometer circuit to determine the Es = 6 V unknown emf's of two batteries E1 and E2. When the first battery El is connected the balancing length I is found to be 50 cm and when the battery E2 is connected the balancing length l is 20 cm. For this case the following statement is accord:

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A lab technician wants to measure the electric current flowing through a circuit. The circuit consists of a load Resistor R=4Q connected at the terminals of a battery with internal resistance r=20 and emf e = 10V. The lab technician being amateur connects the (ideal) Ammeter WRONGLY in parallel to the battery. A 2.00 N 10.0 V 4.00 Q ro kaaen . g ny Find: 1. The current through the 4Q load resistor. 2. The current supplied by the battery. 3. The terminal voltage of the battery. 4. The current flowing through the 42 load resistor BEFORE the technician connects the Ammeter. 5. What would the correct way to connect the Ammeter be?
An electric circuit has a battery with an EMF of 1.50 V. Its positive terminal is connected to its negative terminal by a copper wire in a circular loop having a radius of 0.500 m. Solve for the drift velocity in the wire if there is one free electron per copper atom. Detailed assumptions: - The size of the cell is negligible compared to the length of the circuit. Copper resistivity: p 1.80x10-00-m Copper density D- 8.96x10° kg-m kg-m-3 - Copper relative atomic mass: ma = 63.5 g/mol Express your answer in mm/s.
A student performs a lab where the voltagedrop across a resistor is measured as a functionof current. Plot a graph from the values givenin the following table, and determine theresistance of the circuit. Current, I (mA) Potential Difference, Current, I (mA)V (V)0.00 0.00200 9.00400 16.0600 24.0800 31.01000 40.0
The figure below shows how a bleeder resistor (R = 246 kN) is used to discharge a capacitor (C = 63.7 µF) after an electronic device is shut off, allowing a person to work on the electronics with less risk of shock. Electronic circuit (a) What is the time constant? S (b) How long will it take to reduce the voltage on the capacitor to 0.100% of its full value once discharge begins? S (c) If the capacitor is charged to a voltage Vo through a 133 2 resistance, calculate the time it takes to rise to 0.865V, (this is about two time constants).
An ideal battery with emf, & = 3 V, and four circuit resistors, R₁ = 230 2, R₂ = 150, R3 = 460 , and R4 = 590 , are wired together as shown in the diagram. (a) Find the equivalent resistance of the circuit. Req 324.92 (b) How much current flows through the battery? 1 = 9.23 mA (c) What is the voltage between points a and b? Vab= 0.876 ✓ V (d) Find the current through each resistor. 4₁ = 9.23 12 = 5.84 13 = 3.39 14 = 3.39 = mA mA X mA X mA (e) At what rate is energy being dissipated in the circuit? mW W R₁ b -R₂ R3 w R4
An initially uncharged 4.15 µF capacitor and a 7.51 k2 resistor are connected in series to a 1.50 V battery that has negligible internal resistance. What is the initial current in the circuit, expressed in milliamperes? initial current: Calculate the circuit's time constant in milliseconds. time constant: ms How much time, in milliseconds, must elapse from the closing of the circuit for the current to decrease to 3.83% of its initial value? elapsed time: ms
A 2.00-nF capacitor with an initial charge of 4.98 ?C is discharged through a 1.31-kΩ resistor. (a) Calculate the magnitude of the current in the resistor 9.00 ?s after the resistor is connected across the terminals of the capacitor. mA(b) What charge remains on the capacitor after 8.00 ?s? ?C(c) What is the maximum current in the resistor? A
A 2.00-nF capacitor with an initial charge of 4.80 μC is discharged through a 1.25-k2 resistor. (a) Calculate the magnitude of the current in the resistor 9.00 us after the resistor is connected across the terminals of the capacitor. mA (b) What charge remains on the capacitor after 8.00 µs? μC (c) What is the maximum current in the resistor? A
A 120 volt household circuit has a 20 amp circuit breaker (maximum). A 600-Watt heater and a 60 ohm light are connected to this source in parallel: A) What is the current through the 60 ohm light? B) What is the resistance of the 600-Watt heater? C) What is the minimum resistance R which could be used in parallel as a third appliance without tripping the 20 amp circuit breaker?
R A 485 resistor, an uncharged 1.50 μF capacitor, and a 6.18 V emf are connected in series. (a) What is the initial current (in mA)? MA (b) What is the RC time constant (in s)? (c) What is the current (in mA) after one time constant? mA Z t Russell 2000 A S S (d) What is the voltage (in V) on the capacitor after one time constant? E 4 R 4 % "C 5 Q Search DEC G 40 B Assignment-Responses/suunt: 6 O 1& H N 4 الالالالالك 4+ M 8 19 autosave 000 32 ctri Protect your privacy with Privacy Camera Kill Switch and Fingerprint Reader Seedisainers ogrodutbox 92 + } pause 2 backspace Built thin and light for those on-the-go M enter hp HP ENVY x360 Get more done with the latest Intel® CoreTM processor. home 4 BANG & OLUFSEN 3-way micro-edge display Audio by Bang & Olufsen 1 9 G 34x 1 8 5 4:30 PM 6/19/2023 BANG & OLUFSEN 3 pg dn ent