B1. A water with viscosity 11.4x10-3 poise is flowing through a pipe of diameter 460 mm at the rate of 400 litres per sec. Find the Reynold's Number & the head lost due to friction in the pipe of length 1.5 km.

B1. A water with viscosity 11.4x10-3 poise is flowing through a pipe of diameter 460 mm at the rate of 400 litres per sec. Find the Reynold's Number & the head lost due to friction in the pipe of length 1.5 km.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is pumped at a rate of 24.33 m/s from tank (A) and out through a 298.05 m pipe to tank (B). The surface roughness of the pipe is 0.046 mm. When the water levels are as shown in the given figure, the head provided by the pump is 70.54 m. Calculate the pipe diameter (mm) if the water temperature is 10°C (do not assume the water mass density and the viscosity). Use f = 0.02 for the first iteration and try only one more iterations (two in total) by using Swamee and Jain formula. Elevation Elevatjon - = 140 m = 135 m Tank (B) Elevation = 100 m Tank (A) pump Elevation = 95 m
Find the cross sectional area of pipe Discharge=77 m3/s Velocity=10 m/s
I need the answer as soon as possible
Water flows at a rate of 500 gal/min through a 400-ft-long line. The first and last 100 ft of the line are 6-in-diameter cast iron pipes, while the middle 200 ft consists of two 4.24-in-diameter cast iron pipes. Find: a. Provide a diagram b. the average velocity in each section of pipe, c. the pressure drop in each length of pipe, and d. the total pressure drop.
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (e = 0.00061 m).Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flowthrough the pipe, what must be the pressure at A? Ans. 314 kPa (show the complete solution with diagram) [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet.E.g. (density, viscosity). Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness]
Hello, kindly help me with this question
Solve it..
I need the answer at 20 minute
Q3: Find the diameter of a circular orifice to discharge (0.015m '/ sec) under a head of (2.4m). If the orifice is in a vertical plane and the jet falls (0.25m) in a horizontal distance of (1.3m) from the vena-contracta. Find the head loss through the orifice
Task 3 - Flow through a Diffuser Water flows at 7.2 m/h through the depicted horizontal diffuser which gradually enlarges from a d, = 40 mm to a d, = 50 mm diameter pipe. Mind units and elementary knowledge. EGL (Bernoulli flow) d1 d2 arbitrary reference plane a) Calculate the head loss h = and the resulting frictional pressure drop Ap, of the 28 dissuser.
B1. A crude oil of specific gravity 0.75 is flowing through a pipe of diameter 275 mm and the frictional head loss of 5 m of crude oil between the two ends of a pipe which are 525 m apart. Calculate the Reynold's Number, discharge of crude oil in the pipe. Take co - efficient of friction as 0.007 and kinematic viscosity as 10 stokes. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The velocity of flow of oil in the pipe is (m/s) The Reynold's Number for the flow is Discharge of crude oil through pipe (in m3/s) is
Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 19 lb/ft^ 3 . What is the mass flow rate? If viscous effects are neglectedTake the specific weight for mercury equal to 846 and for water equal to 62.4 at 68 F