b1 = -7.333 V V2 = v1 +2 = -5.333 V e circuit in the below figure. 3 V 2Ω 7 V

Q: Can you help me identify if the following points are connected and isolated? could you also explain…

A: Based on the given protoboard connection the connection type needs to be identified for the…

Q: Explain this diagram for a dummy

A: The given circuit is as shown below,

Q: ?How many nodes in this circuit R₁ R₁ W

A: Circuit diagram is given as,

Q: 2Ω 4Ω 3Ω Ε -10V R2 1N R 5Ω Ε ον 6 V 63.7 mA

A:

Q: R1 R2 1ka + 2ka E2 E1 -10V R4 4ka -10V A R3 3kQ

A: For the given circuit  mesh analysis is perform as shown below

Q: What would R1 be?

A:

Q: Consider the circuit shown below. Find the equivalent resistance at terminal AB. A B R4 = 40 W R₁ =…

A:

Q: +15 Vcc RC 1.5 k2 22 k2 ß = 150, R2 4.7 k. SRE 680 kN

A:

Q: How would you find total Resistance. I found Ra of R7,Rload, and R8 to be 12kOhms. Rb of R6 and Ra…

A: R7, Rload and R8 are series, Ra = 2 + 4 + 6 = 12 kΩRa and R6 parallel, Rb = 12 * 6 / (12 + 6) = 4…

Q: For given value of the circuit, Vsupply = 120 V, and with R₁= 2002, R₂-30.0, R3=75, R4=300, R5=…

A: The required parameter can be calculated by using mesh analysis and ohms law. By using the mesh…

Q: Determine the current passing thru R2 and R3. And Determine the voltage drop in R4 and R1. * A…

A: First we will find out equivalent resistance then total current then current through each resistor…

Q: 5A D Μ 1/4 Ω Μ w 1/2 Ω 21d Μ 1/4 Ω 1/3 Ω 3A Ο ld V3 - 1Ω

A:

Q: Then find current I and V when I 10 N and R2 = 8 2.

A: Given circuit

Q: 5. E, = - R, = 52 R2 = 10 0 R3 =10 0 %3D T. R = 20 0 T = 6 A Rg = 20 2

A: Solve this circuit to find the equivalent resistance Using the given current find the voltage using…

Q: 10MVA 10% G₁ LL X₁ 10 MVA 5% 20MVA 15% G₂ X₂ 8 MVA 4% 20MVA 15% G3

A: We need to find out the equivalent circuit diagram for the power system network.

Q: The values in the schematic are: VIN = 3.5 V, R1 = R2 = 6.6 k0, R3 = R4 = 660 kn, and R5 = R6 = 6.6…

A: We need to find out output voltage for given circuit

Thevenin Theorem

Any linear circuit, no matter how complex, maybe simplified to an equivalent circuit utilizing only a single voltage source and series resistance coupled to a load, according to Thevenin's Theorem. The superposition principle says that all foundational equations must be linear, and the notion of "linear" is still the same (i.e., there should not be any exponentials or roots). This is particularly the case when operating with passive elements like resistors, inductors, and capacitors. However, some components (particularly some gaseous and semiconductor devices like tunnel diode, Schottky diode, transistors like BJT, MOSFET) are nonlinear, meaning their current resistance fluctuates with voltage and current. As a result, circuits made up of these parts are known as nonlinear circuits.