(b). You are given a photodiode D1, a capacitor C₁, a resistor R₁ and an operational amplifier which operates at a supply voltage of 5 V. Draw a clearly labelled circuit diagram showing how you can construct a TIA from the given components for detecting and converting weak optical signals into electrical signals. (c). What component value should it be for one of the electronic components or devices in Q2(b) required for getting the specified signal gain?

(b). You are given a photodiode D1, a capacitor C₁, a resistor R₁ and an operational amplifier which operates at a supply voltage of 5 V. Draw a clearly labelled circuit diagram showing how you can construct a TIA from the given components for detecting and converting weak optical signals into electrical signals. (c). What component value should it be for one of the electronic components or devices in Q2(b) required for getting the specified signal gain?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Stringing of cells in a PV panel Draw the tabbing and bus-bar wires for a 72 cell module using three substrings and a junction box mounted in the typical central location. Each substring is protected by a bypass diode. No precision drawing is needed (i.e. you don't need to draw every single cell, the main arrangement of substring and how you connect to the jnction-box is relevant.
a. Illustrate any differences or similarities between BJT and FET. b. Draw the V-I characteristic of an ideal diode Model. c. Draw the circuit symbol of a common emitter configuration of an NPN transistor.
I need the solution quickly with in 15 minutes
Ex. 1904. The 6025E NI-DAQ card allows several analog input channels. The resolution is 12 bits, and allows several ranges from +-10V to +-50mV. If the actual input voltage is 1.980 mV, and the range is set to +-10v, calculate the LabVIEW display of this voltage (mV). Calculate the percent error where PE = 100* (measured actual) / actual. ans:2
3. Circuit in Figure B.3 is designed to provide a DC voltage of 20 V to a load resistance, RL. The input voltage, Vi, varies from 30 in Table B.1, select one zener diode that is suitable for the above circuit operation. Show relevant calculation to justify your selection. UTM OV to 50 V. Based on the parameters given UTM Rs 0.75 k2 UTM & UTM UTM & UTM UTM UTM V, SUTM & UTM TM 2.5 k2 UTM UTM UTM Table B.1 Zener Diode Vz (V) UTM &UTM & UTM PDMAX (W) ZA UTM UTM ZB 0.5 5 ZC 1 15 ZD 0.5 15 JUTM UTM 5 UTM ZE 20 UTM UTM ZF 0.5 1 UTM UTM20 & UTM & UTM & UTM UTM UTM TM UTM TTM UTM
3. Circuit in Figure B.3 is designed to provide a DC voltage of 20 V to a load resistance, RL. UTM Show relevant calculation to justify your selection. The input voltage, Vi, varies from 30 V to 50 V. Based on the parameters given in Table B.1, select one zener diode that is suitable for the above circuit operation. 5 UTM Rs 0.75 k2 UTM & UTM UTM & UTM UTM 3 UTM TM Vi 2.5 ko 5 UTM 5 UTM VL UTM UTM UTM UTM UTM Pigure B 3 Table B.1 Vz (V) UTM UTM 3 UTM PDMAX (W) Zener Diode ZA UTM & UTM ZB 0.5 5 1 15 ZD 0.5 15 UTM UTM 5 UTM ZE 20 UTM UTM ZF 0.5 1 5 UTM UTM 20 5 UTM & UTM & UTM
b) Draw a fully labelled block diagram of a demodulator suitable for DSB-AM, DSB-SC, and SSB signals. Explain briefly it's operation, and why a simple diode detector would not have been suitable.
Q.7 Light-emitting diode (LED) is simply a diode that is designed to emit light. Voltage drop for LED is 0.8V. What happens to the LED when it is connected to the voltage source as in Figure A1? Why? (Describe in terms of majority carrier movement). LED 5V 1kQ Figure Al
QUESTION 3 a. Design such a power supply with an input Voltage ranging from 10V to 15 V, and a limiting Resistor of 4.0 kn. Specifications of the Zener diodes are; Var is 8 V and Rz is 1000. Your task is to obtain regulated output Voltage within the input voltage range. b. With a diagram describe the operation of a clipper that can clip at two independent levels. c. In the circuit below, the values of Rc = 4.7 kN, RE = 3.3 kN, Vs = 4 V and also Vcc = 10 V and B = 100. Prove that the BJT is operating in the active mode. +10 V Re- 4.7 k +4 V R-3.3 kn
Draw the energy band diagram of a p-n-p* bipolar junction transistor. Show all the relevant energies - conduction and valence band edges, Fermi energies, Intrinsic Fermi energy and built-in potentials. Identify which region is heavily doped. Draw very carefully and in a very tidy manner. No free hand diagrams