12Question 5: Basic pipeline branch determinationСycleB. Fill in the pipeline for he following instructions:AA, B, beq G, C, D, E, F, GA1C. Assume beq G is taken. Does this program execute correctly?Why?A2Hint: beq G means jump to the instruction GАD. What do you need to do (and when, i.e., which cycle) to get thecorrect behavior?Hint: What should happen to instructions C, D, EA457IFIDEXМЕМWBIFIDEXМЕМWB

B. Fill in the pipeline for he following instructions: A, B, beq G, C, D, E, F, G C. Assume beq G is taken. Does this program execute correctly? Why? Hint: beg G means jump to the instruction G D. What do you need to do (and when, i.e., which cycle) to get the correct behavior? Hint: What should happen to instructions C, D, E

B. Fill in the pipeline for he following instructions: A, B, beq G, C, D, E, F, G C. Assume beq G is taken. Does this program execute correctly? Why? Hint: beg G means jump to the instruction G D. What do you need to do (and when, i.e., which cycle) to get the correct behavior? Hint: What should happen to instructions C, D, E

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Identify the errors in the instructions of the following code. Justify your answer. .data One DWORD 1000q, 1000b, 1000h, 10d Con = ($ - Sum) .code main PROC Mov EAX, EIP mov AL, con Mov AL, BL+2 Mov dl, ? MOV CS, one main ENDP END main
Write a sequence of LEGv8 instructions to do the following: set X8 to 100 if the contents of X1 is an odd number and set X9 to 200 otherwise. Do not use division instruction in you code. Instead, you use an AND instruction to test if a number is even or odd. Comment your assembly code.
An example of a control instruction is? a. MOVE O b. LOAD O c. JUMP O d. ADD
Choose the correct answer in the picture below.
We wish to execute a single LC-3 instruction that will subtract the decimal number 33 from R1 and put the result in R2. Can we do it? a. No, because the smallest number that fits 5 bits is -32b. No, because we don't have SUB instruction to subtractc. No, because the smallest number that fits 5 bits is -16d. Yes, we can do it with a single instruction.e. none of the above.
. Please show the stages (IF,ID.EX.MEM.WB) and cycles for each instruction. If there is any, please find the hazards and reorder the instructions to avoid any hazards then show them the number of cycles Iw $s1,0($s0) Iw $s2,4(Ss0) bne $s1,$zero, L1 add $s2,$s2,$s1 L1: Iw $s3,8($s0) add $4,$s4,$s3
I need the answer as soon as possible
What is the value of DX after the instruction (subtraction)? DX = 35F3H BX = 7235HSUB DL, BHSelect the correct response:A.129 B. 3581C. 3581HD. 128
When we return from our little break, we will immediately get back into our discussion of application layer protocols and network programs where we left off.
Multiple choice a. Select an instruction form the following that tests bit position 2 of register CH. a. TEST CH, 2 b. BT CH, 2 c. a and b d. NOTCA. After the execution of instruction NEG AX, what will be the value of AX with initialvalue of 01101101? a. 10010010 b. 10010000 c. 10010011 d. 10010100
Use LDS instead of IN for the following instruction: IN R20, PORTB Select one: Oa. LDS R20, 0x05 Ob. LDS R20, PORTB O C. we cannot use LDS instead of IN O d. LDS R20, 0x25
2. Describe the CF, OF, SF, PF, and ZF values after the following instruction is executed. You can assume each of the flags is set to 0 initially. You also need to write very brief explanations as well for the chosen values. No mark is to be given without explanation. (3 marks) ADD AL,10H; where AL contains 7Fh