B. Design a counter which counts from (0011)2 to (1110)2 using 74x163 IC and external gates. The counter should start counting when an active-low ENABLE (EN_L) input is asserted.

Q: Q2: Explain the role of Stack Register in 8086 Microprocessor.

A: the registers are used to store information in the microprocessor.

Q: Given the 74LS147 Encoder TINKHK6206 Logic Symbol 56679AWN 74LS147 (a) What would be output if input…

A:

Q: ROM

A: ROM Computer-Read only memory, is a memory in which we can read but not write on it, it is a…

Q: Design a three input NOR layout so that rise time and fall time become equal when input logic…

A: Given: A three-input NOR layout so that rise time and fall time become equal when input logic…

Q: 1. Draw the figure showing the types of registers in an 8086 microprocessor. Write the register…

A: There are a total of five registers in an 8086 microprocessor. They are  General purpose registers…

Q: 102 PL Gate Control

A:

Q: Draw the logic diagram and transistor implementation for a (2-2-2) AOI.

A: The logic diagram can be implemented as,

Q: What is interface. What is program block and module block.

A: To verify a design we write verification module and  test bench to check that it meet specification.…

Q: , …. 1210). The counter has the following features: a synchronous Active High Reset a value R can…

A: Write VHDL code for a modulo-13 counter (counting sequence is 010, 110, …. 1210). The counter has…

Q: An ADC has a 0 to 14.5-volt input with a(n) 13-bit output. What would the binary value 00..0111…

A: The solution is given below

Q: A question about 74LS04 IC (a Schmitt Trigger). The pictures show the 74LS04 logic, the connection…

A: According to the question, we need to find the voltage logic at pin 1 and point A and the current…

Q: Part 1: The NAND Gate latch (1) Create the circuit of NAND Gate latch (as shown in Figure 1) on a…

A: The latch is a  device that stores 1 bit of data and it is a level triggered device.

Q: st the disadvantages of Fixed function logic

A:

Q: choose the correct answer If a two-input logic gate produces a output of logic HIGH, only if both…

A: If a two-input logic gate produces a output of logic HIGH ,only if both inputs are different,then…

Q: Q2) B) Use the SAR ADC to convert the analog voltage of (7.28 V) to 8-bit binary. If (VREF = 10V),…

A: Given, Analog input voltage Vin=7.28 V Reference voltage Vref=10 V

Q: Draw a logic diagram of a divide-by-14 counter using IC 7493 and 2-input AND gate.

A:

Q: How do I create a 4 input NAND gate?

A: The solution is given below

Q: 4) Design and draw these memory units with their control circuits. Explain operations. a) A single…

A: As per the rules we can answer only one question, please post the remaining questions as the…

Q: You have a 16-bit timer and you want to configure it to generate an interrupt at a rate of 500 Hz.…

A: MSP430 is an ultra low power micro controller. It is a mixed signal processor with RISC…

Q: a) When does an E-MOSFET act as an open switch? b) When does an E-MOSFET act as a closed switch? c)…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 1) In the mononstable multivibrator using 555 timer, if the output Q = logic (0), what will happen…

A: Answer: 1 ) The capacitor will charge and the transistor will be OFF is correct and remaining…

Q: 31. Consider the following stick diagram. Draw the electrically equivalent transistor-level…

A: According to the question, for the given stick diagram as shown below We need to draw the…

Q: are connect

A: The inverter is a logic gate which invert the input to the output. When the input 0 is given to the…

Q: Transistor- Transistor Logic family are not sensitive to O a. Current drop charge O b.…

A: In this question we will write about TTL family....

Q: A 16-bit successive approximation ADC is to be designed to operate at 50,000 conversions/second.…

A: Given  Nmax=50,000 conversion/s Calculating conversion time TT=1NmaxTT=150,000 conversion/sTT=2×10-5…

Up-down counter

In digital logic and computing, a counter is a device that stores (and sometimes displays) the number of times a particular event or process has occurred, often in relationship to a clock. A sequential digital logic circuit is the most common type with an input line or clock and multiple output lines. In the binary or binary-coded decimal (BCD) number system, the values on the input line represents a number by several flip-flops connected in a cascaded manner. They are manufactured as separate integrated circuits and are widely used components in digital circuits. These are also a part of larger integrated circuits. These are a specific type of sequential circuit like registers or the value of the flip-flops serving as the output.