B- Water flows steadily through a 4-cm diameter pipe that is 10-m long. The pipe wall is porous, leading to a small flow through the pipe wall. The inlet velocity is 10 m/s, and the exit velocity is 9 m/s. Find the average velocity of the water that is passing through the porous Porous wall 4 cm V- 10 m/s 10 m V=9 m/s surface.

B- Water flows steadily through a 4-cm diameter pipe that is 10-m long. The pipe wall is porous, leading to a small flow through the pipe wall. The inlet velocity is 10 m/s, and the exit velocity is 9 m/s. Find the average velocity of the water that is passing through the porous Porous wall 4 cm V- 10 m/s 10 m V=9 m/s surface.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows at 10 m/s through a pipe. The pipe's radius then becomes 40% of its original size. What is the velocity of the water in the narrower section of pipe?
Water at 20°C is being pumped from tank 1 to tank 2 with given conditions. Calculate the power of pump used in the system. (Both tanks are open to atmosphere). Volume flow rate = 10L/s Pipe material = cast iron
Water at 59 F flows through a straight section of a 6-in-ID cast-iron pipe with an average velocity of 4 fps. The pipe is 120 ft long, and there is an increase in elevation of 2 ft from the inlet of the pipe to its exit. Find the power required to produce this flow rate for the specified conditions. Solve fo the relative roughness only
help me answer, thank you.
Consider the incompressible flow of water through a divergent duct, where the inlet has a velocity & section area of 5 ft/s & 10 ft2. If the exit area is 5x the inlet area and the density of water is 62.4 lbm/ft3, solve for the pressure difference. (Please type answer no write by hend)
5. A tapered pipe, through which water is flowing, is having diameter, 30cm and 20 cm at the cross-sections 1 and 2 respectively. The velocity of water at section 1 is given as 3.5m/s. Find the velocity head at section 1 and 2 and also rate of discharge.
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please
A pipe tapers over 60m from 450mm in diameter to 675mm in diameter. The gauge pressure at the inlet is 75 kN/m2 and the gauge pressure at the outlet is 90 kN/m2. If the centreline of the pipe rises at a gradient of 1 in 80 and the energy loss due to friction is 0.01m per metre length determine the flowrate in the pipeline and the velocity at entry and exit.
The velocity profile for turbulent flow in a circular pipe is approximated by a parabola from the center axis to the point very close to the wall where the local velocity is u = 0.6 u,m and the maximum velocity at the center axis as shown in the given figure. The equation for the parabola can be described as u = Um Determine the flow rate if um is 4.51 m/s and the diameter of the pipe is 3.45 m. 0.6um Parabola Um
Water at 25˚C is flowing past a long cylinder at a velocity of 1.2 m/s in a large tunnel. Theaxis of the cylinder is perpendicular to the direction of flow. The diameter of the cylinder is0.12 m. What is the force per meter length on the cylinder
= = Air flows radially outward between the two parallel circular plates shown in the figure below. The pressure at the outer radius, Ro 5 cm, is atmospheric. Find the pressure at the inner radius R¿ 0.5 cm, if the air density is constant, the air flow is inviscid, the volume flow rate is 4.0 L/s, and the plate spacing is h = 0.125 cm. h Po= Patm = 101.3 kPa T = 20°C 777 R₁ Ra
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please