(b) U Let x[n]={, 1, 2, 1, 2, 1, 2, 1, 2, 1, 2, 1, 2, 1, 2, 1, 2, 1, 2, 1, 2,--- and U y[n] = {, 1, 2, 2, 1, 2, 2, 1, 2, 2, 1, 2, 2, 1, 2, 2, 1, 2, 2, 1, 2,...}. If g[n]=x[n]+y[n], calculate the average value of g[n] and the

Q: Instrumentation material. Explain and draw a neat diagram.

A:

Q: In an unbalanced 3-0 system I, = 12- 90° pu negative sequence current I = 4/-150° , zerc %3D…

A: Given: Ia=1∠-90°-ve sequence current (Ib2)=4∠-150°Zero sequence current Ic0=3∠90°Ib=?

Q: There are 4 select lines present in a multiplexer. How many input lines aren present  in the…

A: In this case, there are 4 select lines present in the multiplexer.

Q: Which of the following is not an example of recording devices? O a. Ultra Violet Recorders Ob.…

A:

Q: 2. Convert from Binary to Gray code: 11010100102 = _______________________ Gray code 3. BCD…

A:

Q: 25. a) With neat block diagram, explain the parts of Digital Instrumentation system. b) Write any 2…

A: a) The block diagram of the digital instrumentation system is shown below:  The various parts of…

Q: Problem Statement & Instructions: 1. State the resolution for each Digital Readout (DRO). 2. For…

A: RESOLUTION A measure of the sharpness and clarity of an image or picture is called resolution. It's…

Q: Series connection of switches would normally create O NOR logic gate O NAND logic gate O AND LOGIC…

A:

Q: We write the following code to configure a time delay of around 0.25 seconds. LDI R17, 0XDF L1: LDI…

A:

Q: A circuit has two pushbutton switches connected to pin PB2and PB3 and two LEDs connected to pin PC0…

A:

Q: (i) (ii) (iii) (iv) Calculate the frequency of the PWM signal. Calculate the duty cycle of the PWM…

A:

Q: Draw the state diagram of sequence detector which produce output i when the sequence i01ioi is…

A: The state diagram is visual representation of the sequence. It shows the internal states and…

Q: Consider a 6-bit ADC and full scale voltage measurement range of (0-59).The Resolution will be…

A: Given that : 6 bit ADC range (0-59) to Find Resolution :

Q: Differenciate the combinational and the sequential switching circuit.

A: There is a major difference between combination and sequential circuit. In combination circuit…

Q: Question 7: Look at this PLC off-delay circuit and explain and describe how it will function, in…

A: In industrial automation, a PLC, or Programmable Logic Controller, is a specialized computer used to…

Q: Distinguish between ‘Analog and Digital signals’.

A: Analog signals A continuous signal called an analog signal substitute one time-varying quantity for…

Q: Convert the OCTAL NUMBER 7715. 6 57 5 to decimal number (show the steps in paper

A: Given, Octal number=7715.6578

Q: of the following statements is true for an SCR. It is an on-only controllable switch, which is…

A: There are three types of switches: Uncontrolled switches : In these turn on and turn off can not be…

Q: design a synchronous counter with sequence One, Four, Seven, one,.. Hint: the counter is idle if its…

A: to design a synchronous counter with sequence One, Four, Seven, one,.. Hint: the counter is idle if…

Q: Definition of setpoint, error and offset in process control system

A: To define: Set point, error and offset in process control system.

Q: Draw and label the block diagram of the instrumentation calibration chain.

A: Instrument calibration- Calibrating an instrument is to ensure that the instrument is working…

Q: Enter the following data patterns and record the outputs. Input Switches D. 14 +5V 7495 B • 2 4 Bit…

A: The Parallel-In Parallel-Out shift register is a type of data storage device. This is commonly…

Q: MATCH 1:2 De-Multiplexer A 2:1 Multiplexer 8 data distributor.c data selectors D DO D₁ A D NOT ge…

A: here we have to match the circuits with the given options.

Q: You have following settings for timer1 and adc resigters. TCCR1A = 0; TCCR1B = 4; TIMSK1 = 1; ADMUX…

A: The correct answer is (B)

Q: Which of the following is a programmable peripheral interface? Select the correct response: 82A59C…

A: Answer:option:-4 82C55A

Q: 1 For the figure shown below answer the following questions: B) Is the input sensor type sink or…

A: Although it is known that input type sensor produces a output signal . and intensity of  signal…

Q: What is the maximum time that can be measured with timer 0 given that: The PIC is clocked at 13.5…

A: Given PIC controller frequency = XTAL =13.5 Mhz PSA=1 ,PS <2:0>=1 Timer 0 in an 8 bit timer

Q: QI Compare between CAS and CCS signaling techniques

A: In communication system a call has to be initiated ,maintained and disconnected . This process is…

Q: Vcc R1 RC Q1 NPN 188 8 R2 RE Volts VC

A:

Q: 5) In an astable multivibrator when the capacitor is capacitor is using a 555 timer, the and the…

A: For the above given question we need to define the behaviour of the capacitor.

Q: 6.12 in section 5.5 it was stated that the brushes may be shifted from the q-axis unintentionally,…

A: Armature Reaction: The effect of magnetic field set up by armature current on the distribution of…

Q: Calculate fout and duty cycle from astable 555 timer with R1 1 kN, R2 = 2 kn, and C = 10 uF.

A: Given R1 = 1 Kohm, R2 = 2 Kohm, C = 10 uf To find  Fout and duty cycle

Q: QUESTION 44 The 8259 is a O Low priority interrupt O Tristate buffer Programmable Peripheral…

A: Intel 8259 is a very important device and very commonly with 8085/8086 systems.

Q: What are the types of Time division multiplexing? Explain each type

A:

Q: DUT AN O ipleser CLK Flip-flop Tristate output butler clock SP Observe the OLMC and programmed…

A:

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.