B/ The sprue leading into the runner of a certain mold has a length is 150 mm. The cross- sectional area at base of the sprue is 400 mm². The mold cavity has a volume is 0.002 m². Determine: (a) the velocity of the molten metal flowing through the base of the sprue, (b) the volume rate of flow, and (c) the time required to fill the mold cavity.

B/ The sprue leading into the runner of a certain mold has a length is 150 mm. The cross- sectional area at base of the sprue is 400 mm². The mold cavity has a volume is 0.002 m². Determine: (a) the velocity of the molten metal flowing through the base of the sprue, (b) the volume rate of flow, and (c) the time required to fill the mold cavity.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
Q2 /A/ In casting experiments performed using a certain alloy and type of sand mold, casting made of steel with shape as disk, with diameter =700mm and 30mm thickness , it took 20sec for a solidify Determine the value of the mold constant in Chvorinov's rule
Q.B3. As part of a project, students have been asked to cast an Aluminium disc for use as a flywheel. The flywheel is part of an engine development project and needs to be 200 mm in diameter and 20 mm thick. Green sand casting will be used. The shrinkage associated with this metal and process is 5% at the solidification stage and further 3 % on cooling to room temperature. Aluminum has a density of 2710 kg/m³ and a melting temperature of 660°C. The pouring temperature is 700°C while the specific heat of aluminum is 887 J/kg.K. The latent heat of fusion of Aluminum is 396 kJ/kg. From previous experiments the Chorinov constant for the mold was found to be 10 s/mm². Determine: a.) The dimensions of the pattern (diameter and thickness) that will need to be made for this part (ignore riser and sprue). b.) The time it will take for complete solidification of the part. c.) Assuming an electric furnace at 10% efficiency is used to heat the metal and it takes around 2 hours achieve pouring…
h, is placed on the top of the mold cavity of a closed type sand mould as shown in the figure. If the riser is of constant volume, then the rate of solidification in the riser is the least when the lindrical blind riser with diameter dand height is ratio h: d is Sprue basin Riser Mould cavity
I am in a hurry, I need the answer as soon as possible, please help.
Identify the part which is used to create a hollow shapes in sand casting. O a. Riser O b. Runner O. Core O d. Gates
Down sprue is designed to deliver the molten metal cast iron having density of 8000 kg/m3 having a mass flow rate of 10 kg/s. height of sprue is 200 mm and height of pouring basin is 60 mm a. Find out flow rate of molten metal b. Area of ingate
what are molten metal problems in a casting rocess ?why do those occur?
flו. 3D) امتحان شهري.pdf 1. A square section riser be designed for a sand-casting mold. The casting itself is a quarter-cylinder with a diameter of 12cm and a length 20cm. The total solidification time for this casting = 0.9 min. The square for the riser will have a height-to-width ratio of 2.0. Determine the dimensions of the riser so that it is total solidification time = 1.2 2. A mold sprue is 180 mm long, the cross-sectional area at its base is 2.4 cm?. The sprue feeds a horizontal runner leading into a mold cavity whose volume is 1600 cm?. Determine, volume rate of flow and time to fill the mold.
Q2 /A/ In casting experiments performed using a certain alloy and type of sand mold, casting made of steel with shape as disk, with diameter =700mm and 30mm thickness, it took 20sec for a solidify Determine the value of the mold constant in Chvorinov's rule