b) The speed of a separately excited motor is controlled by a single-phase semiconverter in Figure 1. The field current, which is also controlled by a semiconverter, is set to the maximum possible value. The ac supply voltage to the armature and field converters is single phase, 220 V, 60 Hz. The armature resistance, R,- 0.3 2, the field resistance, Re= 170 2, and the motor voltage constant, Ky 0.71 V/A rad/s. The load torque, TL - 60NM at 1100 rpm. The viscous friction and no-load losses are negligible. The inductances of the armature and field circuit are sufficient enough to make armature and field currents continuous and ripple free. Calculate; i the field current I. ii. the delay angle of the converter in the armature circuit a, and iii. the input power factor (PF) of the armature circuit converter. i, A F1 La R. Rf M 本卒a F2 A2 本

b) The speed of a separately excited motor is controlled by a single-phase semiconverter in Figure 1. The field current, which is also controlled by a semiconverter, is set to the maximum possible value. The ac supply voltage to the armature and field converters is single phase, 220 V, 60 Hz. The armature resistance, R,- 0.3 2, the field resistance, Re= 170 2, and the motor voltage constant, Ky 0.71 V/A rad/s. The load torque, TL - 60NM at 1100 rpm. The viscous friction and no-load losses are negligible. The inductances of the armature and field circuit are sufficient enough to make armature and field currents continuous and ripple free. Calculate; i the field current I. ii. the delay angle of the converter in the armature circuit a, and iii. the input power factor (PF) of the armature circuit converter. i, A F1 La R. Rf M 本卒a F2 A2 本

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How are these two equations derived Maximum Power Criterion Maximum Torque Criterion
A 100V shunt motor is developing 6Hp while operating at an overall efficiency of 86%. The armature and shunt field resistances are 0.06Ω and 50Ω respectively. Determine the SPL.
Write down the specification of motor and stator for (a) DC motor (b) AC motor
4. If the no load speed of DC motor is 1300 rpm and full load speed is 1100 rpm, then its voltage regulation is a) 12.56% b) 18.18 % c) 17.39% d) 18.39%
2. Draw and explain the block diagram of displacement measurement system using strain guage.
Discuss the economic advantages of electric drive
The purpose of a Yoke in a dc machine is to - a. collect the current b. provide protection c. increase output voltage d. convert induced voltage in to DC
The supply voltage to a DC motor is 160V. If the back emf Ez=155V and the armature resistance A6 is 0.250, the armature current is a) 5A b) 10A c) 15A d) 20A 1800 ro/min The frequency
DC machine question
Question 2 a. Figure 1 shows a block diagram of a DC drive system. Diode rectifier AC supply Power converter SCR Firing circuit Regulator Operator's control station Constant-level DC voltage Variable DC voltage Current (torque) feedback Armature Voltage (speed) feedback Fig. 1: DC Drive System Describe step by step the principle of operation of the system. Shunt field
In PMMC instrument, the controlling torque of a pointer is provided by a. control weight b. air damping O c. current coil d. spring
the - ME (B)- Draw the electrical characteristics and mechanical characteristics of d.c differential compound motor