B The gain of an amplifier without feedback is 50 V/V whereas with negative voltage feedback, it falls to 25 V/V. If after a period of time, the amplifier gain falls to 40 V/V, find the percentage reduction in overall gain: (i) Without feedback. (ii) With negative feedback.

B The gain of an amplifier without feedback is 50 V/V whereas with negative voltage feedback, it falls to 25 V/V. If after a period of time, the amplifier gain falls to 40 V/V, find the percentage reduction in overall gain: (i) Without feedback. (ii) With negative feedback.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6. For common-source small-signal FETS, the output voltage is 180° phase shifted with respect to the Q 7. The operating cycle of a Class A amplifier is Q 8. The maximum efficiency of a Class B amplifier is Q 9. In analyzing op-amps, when the non-inverting input pin is at ground and the inverting input pin is also at 0 V for an AC signal, the technique is called as Q 10. is an op-amp application circuit which is useful in low pass filter circuits.
An amplifier without feedback gives an output of 50V into 6% second harmonic distortion when the input is 0.2V. If the negative feedback is applied to amplifier so that the second harmonic distortion is reduced to 1%. a) What value of feedback ratio must be used? b) What input voltage will be required to produce the same output voltage of 50V?
Derive the expression for voltage gain of deffenetial amplifier with two op-amps.
a) List down TWO (2) types of distortion occurs in practical amplifier operation and briefly explain each of them. b) () Discuss THREE (3) characteristics of a Class A power amplifier. (ii) Discuss THREE (3) characteristics of a Class B power amplifier. (iii) List down THREE (3) advantages of class B power amplifier as compared with class A power amplifier's operation.
4. Consider the differentiating operational amplifier circuit. The feedback resistor is 200 kn, and the input capacitor is 20 uF. If a ramp voltage applied across the input which is -2 V after one second. It increases by -2 V every second for six seconds. Calculate the output voltages of the amplifier for each second after the ramp voltage on the input has been applied. From this draw a graph of output voltage against time and compare this to the input voltage.
An amplifier has a gain of 4. Its input is a sine wave with an amplitude of 3mV and an offset of 1V. What will be expected in the output? a.)The output would have an amplitude of 12mV and the offset would be depending on the amplifier design. b.)The output would have an amplitude of 12mV and the offset would be 4V. c.The output would have an amplitude depending on the amplifier design and the offset would be 4V. d.We lack information in calculating this.
Consider the following statement: In feedback amplifiers, concerning the connections between the direct amplifiers and the feedbacks network, a shunt connectiın at the input part servers to set an increased versiın of the input impedance of the direct amplifier, whereas again a shunt connection at the output part services to set a decreased version of the output imdepance of direct amplifier. Explain what is wrong with the statement above by drawing representative circuit diagrams and outlining the necessary calculations.
6) Consider the following multistage amplifier. Draw the corresponding small signal model. Label, Vin, Vo1 and Vo. Do NOT make any approximations. Do NOT perform small signal analysis with this model. Just draw the small signal model. Show your work! Vin Vcc malli Q1 Re1 Vo1 Vcc ww1. Rc2 Q2 Re2 Vo
I need the answer quickly
(1) Describe in detail the relative advantages of Class A and Class B amplifiers. In what types of circuits would Class B be advantageous over Class A (1I) With the aid of signal diagrams, describe two forms of distortion you would expect to observe on an output signal of a Class B amplifier. (III) Describe in circuit terms the advantages of a Class AB amplifier.
3D Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. Determine the output of the third stage stage. a.9 V b.9000 mV c.79.2 V d.792 mV
For the op-amp shown, all transistors have B= 100, VBE = 0.7 V, and VA= 60 V. The %3D output resistance of all CCSS =0 and RL=1.2 kQ. A) Calculate the total gain. B) Calculate the maximum efficiency of the output stage for sinusoidal inputs. C) Redesign the circuit with a class AB output stage and calculate the maximum efficiency for the same load and CCSS? * +5 V 0. 2mA 1mA Ix V1a1 a2 v2 Q6 05 Vo Q3 2mA RL -5 V