(b) Draw open and short circuit characteristics using the following data for 13kV ,150 MW,0.8 pf machine at 50 Hz. If (A) 200 450 600 850 1200 Voltage (kV) 4 8.7 10.8 13.0 15.5 (a) Determine the unsaturated synchronous reactance of the machine (b) Saturated reactance of the machine (c) Machine supplies full load at a pf of o.85 lag with a terminal voltage of 13kV

(b) Draw open and short circuit characteristics using the following data for 13kV ,150 MW,0.8 pf machine at 50 Hz. If (A) 200 450 600 850 1200 Voltage (kV) 4 8.7 10.8 13.0 15.5 (a) Determine the unsaturated synchronous reactance of the machine (b) Saturated reactance of the machine (c) Machine supplies full load at a pf of o.85 lag with a terminal voltage of 13kV

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Each unit of a 100-unit hotel is 12 × 15 ft. In addition, there's a 60 × 20 ft officeWhat's the service demand load for conductor sizing for lighting and receptacles?
2. A single grounding rod electrode is installed in soil. The electrode's resistance to a good known ground is28 ohms. The next ground rod should be installed at least _______ feet away from the first groundingelectrode.A. 15B. 6C. 10D. 25
TII 8.) 4 – 3 kW, 230 V and 3 – 8.5 kW, 230 V clothes dryers are to be placed in a building, the total VA loading to be used for these in the computation for service entrance conductor is: A. 24375 B. 37500 C. 33750 D. 36000
How to verify the validity of the nodal analysis technique in solving electrical networks?
An alternating current completes 3 cycle in 7.75 ms. What is its frequency in Hz? Round your answer to 2 decimal places.
1. The only exception to the need for all information technology equipment to be satisfactorily grounded is where the equipment is A. DC powered.B. backup generator powered. C. double-insulated.D. isolated equipment. 2. Which section of the National Electrical Code lists sizing requirements for wire-type equipment grounding conductors? A. 250.66 B. 250.118 C. 250.4 D. 250.122 3. Which of the following statements about grounding electrical equipment is true?A. If no wire-type equipment grounding conductors are present with the branch circuits, the equipment grounding terminal bar isn't required.B. Grounding electrical equipment increases the possibility of metal parts remaining energized.C. The nonmetal parts of some electrical equipment are required to be connected to an equipment grounding conductor. D. Equipment grounding conductors can be spliced together outside of a grounded metal box. 4. Which of the following is a condition that must be met in order to qualify for the exemption…
Airframe Electrical System Question: Which wire installation type has the best rating and is the most resistive to breakdown in a chemical environment? (Source: FAA AC 43.13-1B/2B)
3.a. There may be installations where grounded conductors of different systems are installed within the sameraceway, cable, or box. In these cases, it's imperative that the system-grounded conductors remainA. spliced.B. disconnected.C. separated.D. buried.3.b. In dwelling units, the maximum allowable voltage between conductors that supply lighting fixtures isA. 220 V.B. 120 V.C. 115 V.D. 110 V.
each tap conductor must be sized using which table in the NEC? a. 250.166 b. 250.102(C)(1) c. 250.66 d. 250.122
10.A. Which of the following is required in each separate service disconnecting means?A. Grounding electrodeB. Service conductorC. Main bonding jumperD. Equipment grounding conductor10.B. When sizing an equipment bonding jumper on the load side of an overcurrent protective device, thesize of the conductor jumper is based on theA. current rating of the protective device.B. size of the feeder's equipment grounding conductor.C. size of the grounding electrode conductor.D. size of the conductors feeding the protective device.10.C. Grounding clamps are typically suitable for connecting how many conductors?A. OneB. ThreeC. FourD. Two
1. The maximum electrical trade size of intermediate conduit is____________. a. 125 mm b. 100 mm c. 24 mm d. 12 mm