b) caliper. What is the significance of this type of measuring tool? With a well labeled diagram explain the operating techniques of micrometer screw gauge and venier

Q: negligible mass. Determine the force (Fin) that the small piston exerts on fluid in small cylinder.…

A:

Q: me design strength (Mu) of the T-beam sh

A: f'(c) =27 MPa, fy = 350 MPaNeed to findDesign strength of beam

Q: From the figure shown which of the following gives the best outside dimension of the square tubing…

A: Given: Length of the column, L = 4.8 m Support condition: One end is fixed and the other end  hinged…

Q: Describe three causes of permanent ground deformation in steel pipelines.You may use sketches in…

A: Permanent land displacement (PGD) is caused by faults in the soil, landslides, or liquefaction.…

Q: What are the three notations used to conduct beam analysis, and which directions are positive, and…

A: As per bartleby answering guidelines, we àre supposed to solve one question in case of multiple…

Q: Referring to the dial gauge shown in Figure , determinea. Accuracyb. Sensitivityc. Range, given that…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: HA ? M = Value Units

A: Given:- P=85Nmean radius = 10mmlead = 3mmμs=0.35To find:-M

Q: An SAE3140 OQT 1300 steel bar with a rectangular cross section of  2 in ( base) by 3.5 in (height)…

A: From table Design Properties of Carbon and Alloy Steels (appendix 3 )   For SAE3140 OQT 1300…

Q: Add FBD & explain work

A: Step 1:Problem StatementYou are provided with the following data for a steel beam:( E = 29,000 )…

Q: Problem #4: [ If the bolt head and the supporting bracket are made of the same material having a…

A: Given:- Bolt head and the supporting bracket are made of same material Failure shear stress = 120…

Q: Drill pipes are one of the most important components in drilling operations. Drill pipes are subject…

A: Free body diagram of the drill pipe-   Pipe length L=26 ft to 30 ftOuside diameter, D=130mmInside…

Q: ensile strength of 67.819 psi. The original gage length was 2 inches

A: Given:- tensile strength=67.819psi originalgauge length =2 inches gauge length2.75 inches To find:-…

Q: The bolt is subjected to the force F. which has components acting along the z. y, z axes as shown.…

A: Given : F = 76 N Alpha = 52 degree Gamma = 50 degree To Find : Determine the angle beta and then…

Q: A Three rods of equal length L and cross section area A, made of material Aluminum, rubber, steel…

A: Three rods made of different material but having equal length L, area A and load F. We need to…

Q: (Problem 4.16 from the text book) The beam shown is made of a nylon for which the allowable stress…

A: We will find neutral axis and permissible stresses.

Q: Determine the tensile development length required a) using ACI Equation, assuming Ktr = 0 b) using…

A: Determine the tensile development length required a) using ACI Equation, assuming Ktr = 0 b) using…

Q: Describe about the Flat-blade dilatometer testing.

A: The Flat Dilatometer Test:

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.