B B |1 in.- 2 in. 250 lb 5/4 1.5 in. 500 lb

Q: The block is subjected to axial loa normal tension developed at poir the distribution of the normal…

A:

Q: Air pressure in the cylinder is increased by exerting forces P = 2 kN on the two pistons, each…

A: Given Data: The outer radius of the cylinder is: rO=47 mm The force exerted on the walls is: P=2…

Q: The cross-sectional area of bar ABCD is 500 mm?. Determine the stress in segment BC. 40 kN 35 kN 20…

A:

Q: Calculate the tension in each cable around the pulley.

A:

Q: Determine the stress components acting on the inclined plane AB. Solve the problem using the method…

A: Given data:

Q: If the force P equals 2500 lbs. Determine the maximum tensile stress in the section of the hook…

A:

Q: The 20 mm diameter rod is subjected to the loads shown. (a) Determine the state of stress at point 4…

A: Diameter, d = 20 mmIt is asked to find the stress at point A and draw the state of stress using…

Q: The bar has a 100 mm by 15 mm rectangular cross section. The allowable normal and shear stresses on…

A:

Q: Use Mohr’s circle to determine the principal stresses at the point. Also, find the corresponding…

A:

Q: The two rods support the vertical force of P = 40 kN. Determine the normal stress in rod AB and AC…

A:

Q: 2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless…

A: Given data: The allowable stress in the cable is, σa=5.2 ksi. The weight of the cylinder is, w=890…

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section…

A: Calculated normal stress at A, B and C and y position where normal stress equals zero

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each…

A:

Q: The block members have a cross section of 2 in x 2 in is joined by a glued scarf spliced as shown.…

A: The ultimate normal stress on the glue surface is The factor of safety is The cross section…

Q: Determine the normal stress developed at points A and B. Neglect the weight of the block.

A: The sum of forces in the horizontal direction, ∑FX=-6 kips -12 kipsF=-18 kips The expression of the…

Q: b. Determine the maximum value of the average normal stress points C and E. 0.4 m c. Determine the…

A: Here we have given P=20 kNdiameter d= 16mm∑mB=020(0.25)=-FCE(0.4)FCE=-12.5 kN (compr)

Q: Current Attempt in Progress The solid 1.35-in.-diameter rod is subjected to a uniform axial…

A:

Q: The solid bar has a diameter of 50 mm. The two forces and the torque Tx are acting at the origin of…

A:

Q: The rib-joint pliers are used to grip the smooth pipe C. If the force of 100 N is applied to the…

A: Given: The magnitude of the force applied on the handles is FH=100 N. The length and breadth of the…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.