/MECH%202013%20-%20Dr.%20James%20Duffy%20-%20August%20Assessm/ 14+ | B O78%Fig. T(a)(b)Answer each of the following for the circuit shown in Fig. 1(b) when the spring in valve 1S3fails (will not extend) after the first activation of valve 1S3.Describe the problem that would result for the second and subsequent activations of(ii)What is the name given to this type of problem?1A182183課1V21V11S21S3 21S12Fig. 1(b)(c)Identify two reasons why indirect control would be used instead of direct control inelectropneumatics.(d)Name the different types of hydraulic relief valves and state the main operation differenceSmarks)between the two types.Page 2 of 14MacBookAir

Answered: Image /qna-images/answer/c3abb76e-32c1-4b15-8611-84ee53d27c11.jpg

(b) Answer each of the following for the circuit shown in Fig. 1(b) when the spring in valve 1S3 fails (will not extend) after the first activation of valve 1S3. (i) Describe the problem that would result for the second and subsequent activations of is1. (ii) What is the name given to this type of problem? 1 A 152 183 1V2 4 1V1 1 1S1 2 2. 1S2 1S3 2 1830 Fig. 1(b)

(b) Answer each of the following for the circuit shown in Fig. 1(b) when the spring in valve 1S3 fails (will not extend) after the first activation of valve 1S3. (i) Describe the problem that would result for the second and subsequent activations of is1. (ii) What is the name given to this type of problem? 1 A 152 183 1V2 4 1V1 1 1S1 2 2. 1S2 1S3 2 1830 Fig. 1(b)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The spring constant of a helical compression spring DOES NOT depend on "O+* 13/ coil diameter material strength t. number of active turns wire diameter
A mass-damper-spring system has m = 5 kg and k = 125 N/m. If the system is critically damped, what is the damping constant c? O0N s/m O 1250 N s/m O 50 N s/m O 25 N s/m
A decision is needed regarding the type of isolator (suspension) to use with a machine that has some unbalance. When placed on an isolator having springs alone, the machine weight causes a 3 mm deflection. When the machine is run at 300 rpm supported on four steel springs both the motion of the machine and force transmitted to the supporting structure are marginally acceptable. A colleague has recommended that the machine be run at a higher speed (500 rpm) and that a different isolator be used. The proposed isolator is deflected by 4 mm under static load and has a damping ratio of 0.25. Do you concur with the recommendation? Justify your response in terms of both machine motion and force transmitted to the structure.
Number four, keep four decimal places Number four, keep four decimal places Number four, keep four decimal places
mechanical principles Explain the natural frequency of vibration in a mass-spring system.
42w6RQJt12D8uMZmCfOin4c7gpb9JWvjWVbvJ89jKd9Tw/formResponse Clear selection A block attached to a spring, oscillates on a frictionless horizontal surface with a period of 0.3 s. The time needed by the block to move (for the first time) from position x = A to x = -A/2 is: O 0.05 sec 0.3 sec O 0.1 sec O 0.15 sec 0.2 sec A simple pendulum consists of a 0.8-kg bob connected to a massless
Determine the stability margin for a vehicle with the following parameters; Parameter Value Units Mass 1,870 kg Wheelbase 2.59 Forward weight bias 46 Front axle cornering 67 kN/rad stiffness Rear axle cornering stiffness 67 kN/rad Provide your answer with the units kNm/rad to two decimal places. Your answer must have the correct sign, be it positive or negative (+/-).
SECTION A Q1. An engine is connected to an unbalanced, rotating shaft as shown in Figure Q1. Viscoelastic shock absorbers are used to mount the engine to a frame. The engine is supported by rigid, frictionless guides that prevent it from moving in the horizontal direction. The shock absorbers can be modelled with a spring-damper system. The spring stiffness of the absorber takes on a value of k = 520 kN/m while its damping coefficient c is unknown. The entire engine-shaft assembly has a mass M of 35 kg. The equivalent mass of the shaft unbalance takes on a value of m = 1.2 kg at an offset distance r = 4 mm rotating at angular velocity w. The unbalanced rotating mass of the shaft results in a force F(t) acting in the vertical direction: F(t) = mw²r sin(wt). The force from the unbalance is causing vibration of the engine within the frame. Whenever the shaft is rotating at its operating speed of 1500 rpm the engine is displaced by a maximum of X = 0.3 mm. OSSEM a) Calculate the magnitude…