(b) A synchronous counter counts through 3-bit prime numbers downwards. Assume the counter starts with initial prime value set to 010 as its first 3-bit prime number. The undesired states will go with their next state to be don't cares. (i) Draw the state transition diagram of a state machine. (ii) Build the excitation table for the state machine. (iii) Find the simplest Boolean expression for the circuit using Karnaugh map. (iv) Implement the circuit diagram with implementation of JK flip flops and logic gates.

(b) A synchronous counter counts through 3-bit prime numbers downwards. Assume the counter starts with initial prime value set to 010 as its first 3-bit prime number. The undesired states will go with their next state to be don't cares. (i) Draw the state transition diagram of a state machine. (ii) Build the excitation table for the state machine. (iii) Find the simplest Boolean expression for the circuit using Karnaugh map. (iv) Implement the circuit diagram with implementation of JK flip flops and logic gates.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need a solution very quickly within
Q4) Design a Register File which includes four 2-bit registers (In total, it includes 8 bits). Each register is named as ala0, b1b0, c2c0, d1d0. Registers are loaded from the S input. In addition to that, there are two input signals, X and Y, to determine which register to select (ie. 00 selectsfirst register ala0 etc). Also there is R signal. When W is zero, the content of the register does not change. When the W is 1 the selected register is loaded with a new value by shifting from the S input. Design this register file by using D flip-flops.
This question is from the subject Digital Logic Design. Assume your register number FA19BSExxx (excluding the dashes -) is in Hexadecimal, where xxx are the three digits of your registration number. a) Represent your registration number in the binary. b) Split the ten digits of your registration into two Hexadecimal numbers M and N, where the left most five digits make number M and the right most five digits make number N. Using r’s complement, subtract N from M. In other words, calculate M – N. Solve the question for registration no SP20-BCS-156.
Q6. Draw logic circuit diagram of the Boolean expression. A'B + A(B' + C) + B(B +C').
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.
Supnorting.cxcentions &interruats Select True/False (T/F) for each statement. Exception usually refers to an event outside of the CPU and interrupt refers to an event inside the CPU. ISelect The CPU checks for exceptions/interrupts after every assembly instruction to get to them tast. Select With polled interrupts, the hardware is responsible to identify the source of the event. Select) With vectored interrupts, the hardware is responsible to identify the source of the event. I Setect)
Design a state diagram to detects 0010100 overlapping input sequence (repeating). The output is at logic level "1" when the sequence is detected, Otherwise the output is "0".
6- Set BX to 4567H, CX to FEDCH and SP to A59FH, then run the instructions: PUSH BX PUSH CX a. What is the new value of SP ? b. Display the memory locations where you pushed the values of BX and CX in the stack.
Using D- Flip flops when input is “0” downwards ((11-10-01-00)) when input is “1”A 2-bit counter will be designed to count the given random sequence (00-01-11-10).a) Construct the state table for the sequential circuit.b) Obtain the simplified input equations for flip-flops.c) Draw the logic circuit for the 2-bit counter.
please help just answer as much as you can, no need to complete all. thank you
It's for Digital logic Design.
14.) Using rising edge JK-Flipflops and Digital Logic Gates, build a 4-Stage Shift Register. I recommend labeling D0, Q0, Q1, etc. Based on the waveforms for the CLK (clock) and D0 input generate the waveforms for Q0, Q1, Q2, Q3. DO CLK QO Q1 Q2 Q3