b) A strain gauge with a gauge factor of 2 is mounted along the longitudinal axis on the top surface of a rectangular steel bar (with Young's Modulus = 200 x 106 kN/m²) as shown in Figure Q3. The bar is 3cm wide and 1cm high across the cross-section. It is subjected to a tensile load of 30kN. Gauge K i) E Tensile loading Figure Q3 Assuming the resistance of each of the three resistors is 1200 and supply voltage E₁ = 10V, determine: The change in the resistance of the strain gauge, if the resistance of the unstressed gauge is also 12002. ii) The output voltage B.. iii) The sensitivity of the measurement, in terms of bridge output versus loading.

b) A strain gauge with a gauge factor of 2 is mounted along the longitudinal axis on the top surface of a rectangular steel bar (with Young's Modulus = 200 x 106 kN/m²) as shown in Figure Q3. The bar is 3cm wide and 1cm high across the cross-section. It is subjected to a tensile load of 30kN. Gauge K i) E Tensile loading Figure Q3 Assuming the resistance of each of the three resistors is 1200 and supply voltage E₁ = 10V, determine: The change in the resistance of the strain gauge, if the resistance of the unstressed gauge is also 12002. ii) The output voltage B.. iii) The sensitivity of the measurement, in terms of bridge output versus loading.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Clear solutions pls. Thank you Given the following Resistances and Capacitors in Series and Voltage Source: R1 = 1 ohms R2 = 10 ohms C1 = 0.007 Farad C2 = 0.008 Farad Vs = 9 Volts Frequency = 6 Hz What is the Total Reactance in ohms?
Given the following Resistances and Inductors in Series and Voltage Source: R1 = 37 ohms R2 = 46 ohms L1 = 3 Henry L2 = 6 Henry Vs = 13 Volts %3D Frequency = 67 Hz %3D What is the Total Inductance?
Given the following Resistances and Inductors in Series and Voltage Source: R1 = 74 ohms R2 = 69 ohms L1 = 4 Henry %3D L2 = 5 Henry %3D Vs = 169 Volts Frequency = 98 Hz What is the Amplitude of the voltage across R1?
Total charge is 750 microcoulomb . Determine values of V1 , V , and C2 .
Solev this question it has 4 parts confusing me alot and X=167 and in part c there's a bit tricky with X by providing a condition so please check
solution is required in detail
Listen Calculate the built-in potential barrier, Vbi, for germanium with N = 10¹4 cm-3 and N₂ = 10¹7 cm¯³. Na cm-3 O Vbi = 0.335 V O Vbi Vbi = 0.312 V O Vbi Vbi = 0.395 V Vbi = 0.253 V
the force between two charges depends on directly to the product of the two charges and inversely to the square of the distance between the two charges directly to the square of the product of the two charges and inversely to the square of the distance between the two charges directly to square of the distance between two charges and inversely O to the product of the two charges inversely to the product of the two charges and directly to the distance between two charges
A K- type thermocouple is used to measure the temperature in a heating process. The length of the bare material is 110mm and thickness is 1mm. Find the time constant of the bare material. Type of Thermo-coupleMaterial K ( W/m-k) Q (kg/m³)s (J/Kg- oc) Iron- Constantan 46 8535 345 K Kromel- Alumel 35 8738 380 T Copper- Constantan 160 8902 316 E Cromel - Contantan 33 8825 336 N Nicrocil- Nisil 34 8702 376 B Pt(30%)Rhodium - Pt(6%)Rhodium 19 15718 56 R Platinum(13%)Rodium - Platinum 55 16628 99 Platinum(10%)Rodium - Platinum 52.9 16745 99 Time constant of the bare material is, T=
Find the equivalent resistance Rab for this circuit
What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mA
A resistance strain gauge with gauge factor of 2 is bonded to a steel member, which is subjected to a strain of 1 × 10-6. The original resistance value of this strain gauge is 120. The change in resistance due to the applied strain is?