(b) A pitot-static probe is use to determine the flow velocity by measuring the differential pressure. The pitot formula to obtain the flow velocity is, 2(P - P) V = where, V is the velocity, P is pressure and pis fluid density. i) The pressure difference sensor use in the system is electronic types and the output of the device is measured in voltage. The output of the pressure device is 3.5 V and the linear relationship between the device and the pressure difference is 10 kPa/V. If the measured fluid is water at 20°C, determine the pressure difference inside the system the water velocity. ii) The Pitot-static tube is also commonly use in aircraft. An aircraft flying at 3000 m above sea level when the differential pressure reading clocked 3 kPa. Determine the speed of the aircraft.

(b) A pitot-static probe is use to determine the flow velocity by measuring the differential pressure. The pitot formula to obtain the flow velocity is, 2(P - P) V = where, V is the velocity, P is pressure and pis fluid density. i) The pressure difference sensor use in the system is electronic types and the output of the device is measured in voltage. The output of the pressure device is 3.5 V and the linear relationship between the device and the pressure difference is 10 kPa/V. If the measured fluid is water at 20°C, determine the pressure difference inside the system the water velocity. ii) The Pitot-static tube is also commonly use in aircraft. An aircraft flying at 3000 m above sea level when the differential pressure reading clocked 3 kPa. Determine the speed of the aircraft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the resistance in each scenario presented. Explain whether the resistance is linear or not, and if not describe the relation, finally, explain how it can be linearized about a specific condition. Be sure to state the units and demonstrate that they are correct using the appropriate pressure/flow relation. a) Laminar flow An aqueous solution of 50% glycerol / 50% water is flowing through a pipe with the following system parameters: System_Parameters = (L = 100.0 D= 0.2 u= 0.022 p= 1150.0 9m=7.0 g = 9.81) units : L ~ m; D~ m; µ ~ Pa · s; p~ kg: 4. ~ 8: Confirm that this is laminar flow and then calculate the resistance. b) Pump Resistance from Pump Curve Consider the following pump curve: [Feet) (Meters] 30어 Find the pump resistance if the pump is supporting 15 meters of discharge head pressure, at a flow rate of 300 L/minute. 80- 250 7어 100 PSI L/min Determine the pump resistance in Pa 20어 6어85 PST 50 SCFM 5어 75 PST Note that standard pump curves are oriented opposite to the…
i need the answer quickly
Q: Experiment of venturi meter. Please give a brief description for Bernoulli’s equation. What typeof parameters can be derived from an experiment?
Please I want answer for this question - 7 . Many Thanks
4G I. uols -a moodle1.du.edu.om IVIGI Ncu vut UI .00 P Flag question Consider the system is the following figure. K = 4 N/m x,(1) K2 = 5 N/m x(1) fy. = 3 N-s/m M =1 kg|Jv2=3 N-s/m M, = 2 kg f= 2 N-s/m The differential equations of the system is [3*, + 5x, +9x, - 3x, - 5x, - f() | 2i, +5i, +5x,-34, - Sx, =0 *, + 6x, +9x, - 3i, - Sx, = 0 |25, + Si, + Sx, - 3i, -5x, = /(1) |+6i, +9x, - 3x, -5x, = 0 i, + 6i, +9x, - 3x, - 5x, =0 b. d. li, + 5i, +5x, - 3x, - x, = f(0) LE, + 5i, + 5x, - 34, -4x, = f() Select one: O a. d b. a O c. C O d. b Previous page Finish attempt ... 1 Test 1 Jump to... Grades Assignment 1 and Test 1
Whats the answer ignore what I put in
Need help with engineering problem. Match the RTT term with its explanation: A: ddt(∫CVβρdᏉ) B: ∫CSβρVcosθdAout C: ∫CSβρVcosθdAin A. B. C. Match one of the following answers below to each letter. A change within the control volume Outflow of B from the ontrol volume Inflow of B to the control volume
For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical parameters, the density of working fluid (p), and density of the manometer liquid (pm) as 4. Q = f(D, D2, A2, g, h, Pmv Pr) %3D Write down the balance equations and show your work to end up with an expression for the volumetric flow rate in terms of the variables defined above.
When a fluid flows over a surface, the shear stress I (N/m) at the surface is given by the expression du dy surface where p is the viscosity (N-s/m), u is the velocity parallel to the surface (m/s), and y is the distance normal to the surface (cm). Measurements of the velocity of an air stream flowing above a surface are made with an LDV (laser-Doppler-Velocimeter). The values given below were obtained. y y 0.0 0.00 2.0 88.89 1.0 55.56 3.0 100.00 2 At the local temperature, p = 0.00024 N-s/m. In four decimal places, calculate du/dy at the surface using all the points. Answer =
Cauchy's ΣF ) equation of motion : pDV/Dt =pg + VT (like pa Newtonian viscous stress relations by the tensor relation : Ti j = - pôij + µ[Əvj/əxi + əvi/axj] where dij is the kroneker delta function (1 for i = T includes pressure and viscous surface forces. into Cauchy's equation, and assume constant viscosity, to get the Navier-Stokes vector eq'ns : pDV/Dt Pg -vp + μ^2 V the acceleration DV/Dt av/at+ (VV)V, which for steady state flow gives DV/Dt =(V.) V. Because (VV) V is a non-linear term on the LHS of the N-S equation Reynolds Number RepVL/μ, a measure of the ratio of inertial to viscous forces. : Patm 10^5 = = N = N = ; pwater 1000; pair 1.2; μwater 10^-3 N s/m^2 ; Hair 2 x 10^-5 N•s/m^2 ; g 9.8 m/s^2 = j; 0 for i j ); N
Measurements at a certain point of a pipe have been done where the following parameters were recorded: Fluid of density = 887 kg/m3, Fluid velocity = 4 m/s, Pressure= 11.3 KN/m2 If the total energy per unit weight at this point = 32 m, then the potential energy is: