b) A lkQ resistance is connected across the secondary winding of a 200V/400V transformerwith the following equivalent circuit parameters, Kleq=502, Rc = 10k2, XM =1 k2 , ^leq= 100 2. Determine the following:Ri. The Open Circuit Output Voltage (Vsoc)ii. The Output Voltage under load (Vs)i1i. The Output Current (Is)iv. The Transformer Efficiency (%)

Answered: Image /qna-images/answer/d13995fd-2404-4d07-b7a1-fd299a1ba2d5.jpg

b) A lk resistance is connected across the secondary winding of a 200V/400V transformer with the following equivalent circuit parameters, Rleq=502, Rc = 10kO, XM =1 k2, Xleq = 100 2. Determine the following: i. The Open Circuit Output Voltage (VSoc ii. The Output Voltage under load (Vs) iii. The Output Current (Is) iv. The Transformer Efficiency (%)

b) A lk resistance is connected across the secondary winding of a 200V/400V transformer with the following equivalent circuit parameters, Rleq=502, Rc = 10kO, XM =1 k2, Xleq = 100 2. Determine the following: i. The Open Circuit Output Voltage (VSoc ii. The Output Voltage under load (Vs) iii. The Output Current (Is) iv. The Transformer Efficiency (%)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 RL out OV 10 kN IN4001 alll
How does the coupling factor affect the primary and secondary voltages? For example if the turns ratio in my transformer is 1:2 and the Vin is 10V, the voltage on the primary side is 10V and the voltage on the secondary side is 20V when the coupling factor (k) is 1. What will the primary and secondary voltages be if the coupling factor becomes 0.5?
4.) A transformer has a primary coil with 300 windings, and secondary coil has 400 windings. The input AC power supply is 120 volts (Vrms). A) Is this a step-up or step-down transformer? B) What is the rms voltage across the output terminals (Vrms)? C) What is the peak voltage across the output terminals (Vmax)? Primary Secondary imm ac input
The rated power of a certain transformer is 1 kVA. The transformer operates at 60 Hz and 120 V ac. at 60 Hz and 120 V ac. The secondary voltage is 600 V. (a) What is the maximum current at the load? (b) What is the smallest RL value that can be excited? (c) What is the largest capacitor that can be connected as a load?
A Buck converter has an output power of 1950 Watts, and a source voltage of 1000V (the constant DC voltage). Using the information provided and the "“transformer-like" relationships derived in class, estimate the corresponding load currents for the following duty ratios: a) D=0.35 b) D=0.9 c) D=0.5
A three-phase uncontrolled bridge rectifier delivers power to a resistive load of 10.The output voltage of the rectifier is 400 V DC. The rating of source side of three phasedelta – star transformer is
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R 10 kn IN4001
The maximum efficiency of a 200KVA, 6000/230volt, 50HZ, single phase transformer occurs at half load and is 95% at unity power factor. What is the full load efficiency at 0.7 power factor?
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R1 V out 10 kN D2 IN4001 allle
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
A three-phase uncontrolled bridge rectifier delivers power to a resistive load of 102.The output voltage of the rectifier is 400 V DC. The rating of source side of three phasedelta - star transformer is,