B 25°

Q: A and B, each with mass 5 kg, are connected by the linkage illustrated. If the coefficient of static…

A: Here, from geometry-

Q: Block A has a mass of 50 kg, and block B has a mass of 15 kg. They are stacked, connected by a cable…

A:

Q: A 25 kg crate has a speed of 2 m/s when a forces of F = 0.5(s)+75 N is applied (where t is in…

A: The frictional force is directly proportional to the normal force of the object.According to the…

Q: A 130-lb crate is being transported by a 175-lb hand- truck cart along the frictionless floor. The…

A: To Find:The smallest ratio d/b for which the box will tip before it slides.Given:The force is

Q: The coefficient of static friction between the 225 kg crate and the ground is μs = 0.3, while the…

A: draw FBD of the system

Q: A motorcyclist in a circus rides his motorcycle within the confines of the hollow sphere. The…

A: Answer: The minimum speed at which he must travel if he is to ride along the wall when θ = 90° is…

Q: A car of mass 700 kg travels round a horizontal curve of 60 m radius. The centre of gravity of the…

A:

Q: the following most nearly gives the force P to cause the impending motion of block B to the right.…

A:

Q: A 2600-lb car is moving at a speed of 66 mph when the brakes are fully applied, causing all four…

A:

Q: Consider the three masses A, B and C, respectively 1 kg, 1 kg and 5 kg, connected through the system…

A: Given data :-Mass of A = 1kgMass of B = 1kgMass of C = 5kgPulleys are massless and…

Q: Block A has a mass of 40 kg, and block B has a mass of 8 kg. The coefficients of friction between…

A:

Q: A 20-lb block rests on a rough surface with coefficients of friction = 0.37 and μ = 0.25. Determine…

A: Weight of the block, W= 20 lb Coefficients of friction, μs= 0.37  and  μk= 0.25 Force applied, F= 5…

Q: Problem 2 Block A has a mass of 50 kg, and block B has a mass of 15 kg. They are stacked, connected…

A:

Q: Determine the maximum acceleration of a train in which a box lying on its floor will remain…

A: When friction force is equal to inertia force        ( mass X acceleration ) then the box will be at…

Q: A brake mechanism is used to lower body A with a constant velocity of 3.0 m/s. The coefficient of…

A: Given:To find:(a) Mass of body A.(b) Power dissipated by the brake.

Q: determine the acceleration of block A when the system is released. the coefficient of friction and…

A: Free body diagram of the blocks and their geometry is shown below: The length of cord is constant…

Q: The coefficient of kinetic friction between the50-kg crate and the ground is HE 0.3. The crate…

A:

Q: :--1 manning 1. Define both the coefficients of static and kinetic friction. Explain the 2. Blocks…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: Assume that a driver (car modeled as a point mass) is negotiating a circular turn with a radius of…

A: Given:r=160 ftm=3800 lbμ1=0.85

Q: A 16-lb spool is at rest on an inclined surface. Around its center a cable is wound which travels…

A:

Q: Give a detailed Handwritten solution,If it is a Chatgpt answer i will report.

A: Step 1:Step 2:Step 3:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.