Answered: B 2 A 100N AB=10 cm CB=BD%3D4 cm AF=2cm… | bartleby

Related questions

Question

D
B
2
8-45
100N
AB=10 cm CB3DBD%3D4 cm AF=2cm
In the mechanism shown above, the friction
coefficient of the sliding limb is given as 0.3. A
horizontal force of 100 N is applied from the F point.
Calculate the torque required for the AB crank handle
to start SYT (Counter Clockwise) motion.

Expert Solution

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

You have a grindstone (a disk) that is 77.0 kg, has a 0.400-m radius, and is turning at 89.0 rpm, and you press a steel axe against it with a radial force of 16.0 N. (a)Assuming the kinetic coefficient of friction between steel and stone is 0.50, calculate the angular acceleration (in rad/s2) of the grindstone. (Indicate the direction with the sign of your answer.) rad/s2 (b)How many turns (in rev) will the stone make before coming to rest? rev
Please solve, thank you!
A plane with a wingspan of d = 16 m loses control in flight and begins to spiral in a circle around the cockpit while in a vertical dive. It completes one rotation every t = 3.1 s.
Plz use g = 9.8 m/s2 to find if needed
Macmillan l A motorized wheel is spinning with a rotational velocity of wo = 1.81 rad/s. At t = 0s, the operator switches the wheel to a higher speed setting. The rotational velocity of the wheel at all subsequent times is given by w (t) = woarctan (c + b1²) where c = 1.5574 and b = 6.09 s-². At what time tamax is the rotational acceleration at a maximum? tamax = What is the maximum tangential acceleration a, of a point on the wheel a distance R = 1.29 m from its center? a₁ = What is the magnitude of the total acceleration of this point? a = ms m/s² m/s²
A turn table starts from 10 rad/s of angular velocity and slows down to a stop in 5.0 s. Find the total angle turned during this time, in rad. Hint: use rotational kinematics formula. Assume initial angle and final angular velocity as zero.
A grindstone has a moment of inertia of 6 x 10-3 kg m2. When a constant torque is applied, the flywheel reaches an angular velocity of 1200 rev/min in 15 s. Assuming it started from rest, find the angular acceleration. Find the unbalanced torque applied. Find the angle turned through in the 15 s. Find the work W done on the flywheel by the torque.
Crank OA is rotating at a counterclockwise angular rate of 9.4 rad/s, and this rate is decreasing at 4.3 rad/s². Determine the angular acceleration AB of link AB for the position shown. The angular acceleration AB is positive if counterclockwise, negative if clockwise. 100 mm 9.4 rad/s 85 mm Answer: CAB= 38° G AB=210 mm B rad/s²
A string holds and wraps around a solid cylinder (7-kg and R = 3-m). A person pulls the string vertically upward, so the cylinder’s center of gravity does not move and is suspended in midair for 3 second. Note that the rotational inertia of the cylinder about its axis is MR2/2, the tension in the string is 3-N. what is the net force on the cylinder in Newton?
PLEASE SEND THE ANSWER IN 10 MINUTES !!! Find the magnitude of the net torque on the wheel in Figure below about the axle through O, taking a=13cm, b=41cm. The magnitude of the applied forces are F1=11N, F2=20N, and F3=11N. Provide your answer in units of m⋅N and round off your answer to 2 decimal places.