I need the answer as soon as possible B-12-6. A regulator system has a plantY(s)U(s)10(s + 1)(s + 2)(s + 3)Define state variables asyX2 = ijX3 = 2By use of the state-feedback control u =to place the closed-loop poles at sKx, it is desired|li (i = 1, 2, 3), where-2 + j2V3.-2 – j2V3,l3 = -10%3DHz =Determine the necessary state-feedback gain matrix K.

We have Given system YsUs=10S+1S+2S+3state variables are;x1=yx2=x1.x3=x2.state feedback control…

B-12-6. A regulator system has a plant Y(s) 10 U(s) (s + 1)(s + 2) (s + 3) Define state variables as X, = y X2 = ij X3 = i2 %3D By use of the state-feedback control u - - Kx, it is desired to place the closed-loop poles at s = µ; (i = 1,2, 3), where -2 + j2V3. Hz = -2 - j2V3, M3 = -10 Determine the necessary state-feedback gain matrix K.

B-12-6. A regulator system has a plant Y(s) 10 U(s) (s + 1)(s + 2) (s + 3) Define state variables as X, = y X2 = ij X3 = i2 %3D By use of the state-feedback control u - - Kx, it is desired to place the closed-loop poles at s = µ; (i = 1,2, 3), where -2 + j2V3. Hz = -2 - j2V3, M3 = -10 Determine the necessary state-feedback gain matrix K.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
What is the lighting and receptacle demand load for an 1000 sq. m office space with one hundred ten, 15 A, 250 V receptacles. [Office General Lighting Receptacle]
What is RG rating of coaxial cable. Please give me detailed information. Don't copy previously given Answer
I need the answer as soon as possible
Assuming all terminals are rated 75°C and you have a #10 AWG THHN/THWN conductors in a conduit and the conduit is run on the roof off a office building where the ambient temperature never rises above 30°C the largest size circuit breaker or fuse permitted to protect these wires is:?
Can I use a distribution box on every floor to distribute telephone lines to their designated outlets?
The only way to reach any of the levels where ABC Company is located in a building with ten stories is to use the elevator. In addition, those on the ninth and tenth levels need to connect to a group of servers located on the eighth. Describe the best wiring for the lift shaft. Pick the best option if there is more than one and justify your decision. If you think that interfloor connections may need to operate at substantially greater rates in the future, you may want to reconsider your current option. What is the optimum media for unbounded data transfer requirements? Justify your response.
Please answer in typing format
i need the answer quickly