Axial P to the square cross section 5 m long AB column given the loading condition and dimensions in the figure pressure force is acting. Accordingly, find the P that the column can carry without buckling. The B end of the column is anchored and the safety number for buckling is n =3 (2<2, =105 → 0, =31000–1142 N / cm² ve E = 2,1×10’ N/ cm² )

Axial P to the square cross section 5 m long AB column given the loading condition and dimensions in the figure pressure force is acting. Accordingly, find the P that the column can carry without buckling. The B end of the column is anchored and the safety number for buckling is n =3 (2<2, =105 → 0, =31000–1142 N / cm² ve E = 2,1×10’ N/ cm² )

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the reactions for the beam shown if the vertical deflection at support B is zero. 3.0 kip/ft O B 16' 8' SIMPLE BEAM: CONCENTRATED LOAD AT ANY POINT SIMPLE BEAM: UNIFORMLY DISTRIBUTED LOAD Pb R = V, (max when a b) R V, . Pab w V M max (at point of load). M max (at center) Pbx Shear M, (when x b) = Pab(a + 2bN3a(a + 2b) M max Amax (at center), 27EI Pah2 384EI M max Moment A, (at point of load) 3EII WX (3 – 21r2 + x³) Pbx (2 - b2 - x) 4, 24EI 4, (when x
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a= 1.5 m, b= 1lm, d=30 mm, h= 8 mm 2а b a - a
Static please give the correct answer. Thank you
A beam is made up of two identical bars AB and BC, by hinging them together at B. The end A is built-in (cantilevered) and the end C is simply- supported. With the load P acting as shown, the bending moment at A is 14 L B O L/2 P 4 L
The beam AB will fail if the maximum internal moment at D reaches 800 N • m or the normal force in member BC becomes 1500 N. Determine the largest load w it can support.
Determine all the internal force for each member.
For the frame and loading shown, determine (a)the reaction at D, (b) the force in member BE.
A)determine determinacy and stability b) identify the zero force members
The bar is snugly fit between points C and A before the loading is applied at Collar B. Assume E = 200 GPa for the steel. The circular bars in the assembly are solid. The bars are solid with a diameter of 15 mm. Assume a fixed rigid support at C and A. A C В 6 kN 3 m 2 m A) Show the FBD and compatibility equation for this problem. B) Determine the support reactions at A and C. (Horizontal forces only) Left side: Fc = Right side: FA =
5
Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter of d. If the load P on the beam causes the end C to be displaced h downward, determine the normal strain developed in wires CE and BD and the applied load P. Assume E steel = 200 Gpa and a=lm, b= 1.75m, d=50 mm, h= 6mm E D 2a b
Consider the frame as shown in the figure. A moment of 80 kN-m acts at the joint O, given that the support at B fails at any moment greater than 18 kN-m. Then support B is (a) Unsafe (c) Just Safe A L, EI D L, EI D 80 kNm B L, EI L, EI C (b) Safe (d) Cannot be determined