At the instant shown, car A travels along the straight portion the road with a speed of 25 m/s. At this same instant car B travels ng the circular portion of the road with a speed of 15 m/s. Determine = velocity of car B relative to car A. (VBA= p=200

Q: Determine the Resultanto f the eoplanar orcesestem

A:

Q: what is 6 to 10 po?

A:

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: y' = -y tan x, y(0) = 2

A:

Q: For the frame shown below, Is supported by pins at C and D. Determine the magnitude of reaction at C…

A: Consider the free body diagram of the member CBA as shown below.

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: 1. What is the type of robot?

A: ***As per our company policy we are supposed to do only 1 question if you need the rest please…

Q: дл др Os ӘТ S Cp

A: Write the expression at constant enthalpy. dh=Tds+vdP0=Tds+vdP∂s∂ph=-vT

Q: Water falls vertically downward from an open faucet with an initial velocity of 47 cm/s. If the…

A:

Q: (a) Determine the -position of the centroid of the figure shown on the next page. (and draw it on…

A:

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: Draw the box closing mechanism given in the figure in the given dimensions. Determine the velocities…

A:

Q: ) The disk is rotating about point O with an angular velocity x=7 rad/s in the given direction. Rod…

A: Given Data: The angular velocity of the disc is ωo=7 rad/s. The value of other variables are r=4 m,…

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: You are designing a new engine; this device operates with liquid fuel as an input and gener energy…

A: Hello. Since you have posted multiple questions we will solve the first question for you. If you…

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Q: Tät-/e205+(17-78 2.

A: Given Data⇒a↦=202+17.782

Q: (4) 8.8.8.8 16 8 8 16 21

A: the question is not fully asked   bricks and blocks are given

Q: Add the length of all the horizontal pieces. They go left and right.

A:

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: how can I get the 85 α

A:

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: So what is the answer? What is y (1)? What is the answer up to two decimal places.

A: y(1) for equation of motion

Q: continue the question

A: Given: (d) The dimension of the plate: →A=1.2m*1.2m Because the distance of the center of gravity of…

Q: Findss 30 kN-m

A:

Q: (12m) ladder weighs 200N and is ed against a smooth vertical wall its lower and (6m) from the wall

A:

Q: M, B

A: Given data, The reaction at A and B can be calculated as -

Q: How did you get the value of "F"

A:

Q: What is the normal force applied to the block?

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.