At t = 0 a grinding wheel has an angular velocity of 24.0 rad/s. It has a constant angular acceleration of 30.0 rad/s2 until a circuit breaker trips at t = 2.00 s. From then on, it turns through 432 rad as it coasts to a stop at constant angular acceleration. (a) Through what total angle did the wheel turn between t = 0 and the time it stopped? (b) At what time did it stop? (c) What was its acceleration as it slowed down?

At t = 0 a grinding wheel has an angular velocity of 24.0 rad/s. It has a constant angular acceleration of 30.0 rad/s2 until a circuit breaker trips at t = 2.00 s. From then on, it turns through 432 rad as it coasts to a stop at constant angular acceleration. (a) Through what total angle did the wheel turn between t = 0 and the time it stopped? (b) At what time did it stop? (c) What was its acceleration as it slowed down?

Similar questions

At t = 0, a wheel rotating about a fixed axis at a constant angular deceleration of 0.51 rad/s2 has an angular velocity of 0.8 rad/s and an angular position of 7 rad. What is the angular position of the wheel after 2 s in rad units?
A cylinder with rotational inertia I₁ = 2.6 kg. m² rotates clockwise about a vertical axis through its center with angular speed @₁ = 5.6 rad/s. A second cylinder with rotational inertia 12 = 1.3 kg m² rotates counterclockwise about the same axis with angular speed @₂ = 6.4 rad/s. If the cylinders couple so they have the same rotational axis, what is the angular speed of the combination (in rad/s)? rad/s What percentage of the original kinetic energy is lost to friction? % +
In the figure, wheel A of radius ra = 13.3 cm is coupled by belt B to wheel Cof radius rc=20.4 cm. The angular speed of wheel A is increased from rest at a constant rate of 1.43 rad/s2. Find the time needed for wheel C to reach an angular speed of 58.1 rev/min, assuming the belt does not slip. (Hint: If the belt does not slip, the linear speeds at the two rims must be equal.) TA Number i Units
In the figure, wheel A of radius -9.40 cm is coupled by belt B to wheel C of radius rc-26.1 cm. The angular speed of wheel A is increased from rest at a constant rate of 2.53 rad/s². Find the time needed for wheel C to reach an angular speed of 63.0 rev/min, assuming the belt does not slip. (Hint: If the belt does not slip, the linear speeds at the two rims must be equal.) Number Ma Units B
The angular acceleration of a wheel is a = 7.0t4 - 5.0t², with a in radians per second-squared and tin seconds. At time t = 0, the wheel has an angular velocity of +6 rad/s and an angular position of +6 rad. Write expressions for (a) the angular velocity (rad/s) and (b) the angular position (rad) as functions of time (s). (a) Number i i (b) Number i Save for Later Units t+ i +5. i tó i Units t³+ +4+
At time t=0 a grinding wheel has an angular velocity of 27.0 rad/s . It has a constant angular acceleration of 34.0 rad/s^2until a circuit breaker trips at time t= 2.20 s . From then on, the wheel turns through an angle of 438 rad as it coasts to a stop at constant angular deceleration. a) Through what total angle did the wheel turn between t=0 and the time it stopped? Express your answer in radians. b) At what time does the wheel stop? Express your answer in seconds. c) What was the wheel's angular acceleration as it slowed down? Express your answer in radians per second^2.
A truck's wheel (R = 0.72 m) is traveling at an initial angular velocity of 12.66 rad/s and is constantly decelerating at a rate of 3.51 rad/s2. How far in meters will a point on the outer rim of the wheel travel by the time it stops? Round your answer to 2 decimal places.
A rotating wheel requires ?=10.4st=10.4s to rotate through 113113 revolutions. Its angular velocity at the end of this 10.410.4-s interval is 28rad/s28rad/s. What is the constant angular acceleration of the wheel? Express your answer in units of rad/s2rad/s2 using one decimal place.
A grinding wheel attached to an electric motor is initially rotating at 116 rev/min when it is suddenly switched off and comes to rest. Assume the wheel undergoes a uniform angular acceleration – 1.98 rad/s?. Through how many radians does the wheel turn in coming to a stop? {Note you'll have to convert rev and time units} O 28.5 rad O 55.6 rad O 37.3 rad O 43.1 rad O 14.7 rad MacBook Air 80 888 DII esc F3 F7 # $ % & 3 4 7 8 W R Y A D F G H J K C V
The angular acceleration of a rotating rigid body is given by a = (7.0 2.0t) rad/s². If the body starts rotating from rest at t = 0, answer the following. (a) What is the angular velocity? (Use the following as necessary: t. Assume t is in seconds and is in rad/s. Do not include units in your answer. Enter a mathematical expression or equation with exact values.) @= (b) What is the angular position? (Use the following as necessary: t. Assume t is in seconds and is in radians. Do not include units in your answer. Also assume the body starts at 0 rad. Enter a mathematical expression or equation with exact values.) 0 = (c) What angle (in rad) does it rotate through in 2.0 s? (Indicate the direction with the sign of your answer. Round your answer to at least 2 decimal places.) rad (d) What is the angular position at t = 2.0 s? (Give your answer in degrees counterclockwise from the +x-axis, where 0° lies along the +x-axis.) counterclockwise from the +x-axis
The angular acceleration of a wheel is α = 7.0t4 – 5.0t2, with α in radians per second-squared and t in seconds. At time t = 0, the wheel has an angular velocity of +7 rad/s and an angular position of +1 rad. Write expressions for (a) the angular velocity (rad/s) and (b) the angular position (rad) as functions of time (s).
Starting from rest at t = 0 s, a wheel undergoes a constant angular acceleration. When t = 1.9 s, the angular velocity of the wheel is 4.1 rad/s. The acceleration continues until t = 15 s, when the acceleration abruptly changes to 0 rad/s2. Through what angle does the wheel rotate in the interval t = 0 s to t = 40 s?