At stationary the tension in pulley 120N. Find tension in each side and Power tran when belt is on the point of slipping on smaller wheel. The wheel is 250mm diameter and Fac of Friction 0.32. The angle of Lap 165°. The wheel speed 1200 C/min.

Q: Prob # 9. Find the horsepower transmitted by a pair of friction wheels, the diameter of driving…

A:

Q: The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in…

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: 3. Find the tension in each wire, neglecting the masses of the wires. S. 45° System of interest- 30°…

A: Since you have posted multiple questions, we will provide the solution only to the first question as…

Q: .A centrifugal clutch has four shoes which suae i the driving shaft and make contact with the…

A: Given:  The number of shoe, n  = 4 The clearance , c = 5 mm = 0.005 m The internal diameter of the…

Q: Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a…

A: Given data as per the question Radius of drum=4 inchμ=0.7Braking Torque=400 lb in

Q: o having a diameter a (960 rpm) and inert d (3.2 kg.m²) respe

A:

Q: (A) If the power losses in Pelton wheel due to bucket friction is given by 1 POK (V, -u) where K is…

A:

Q: Blocks A and B weigh 250N and150N, respectively. Using the coefficients of static friction indicated…

A: Weight of block A = 250N Weight of block B = 150N Weight of block E = W To find: FBD of pulley C,D…

Q: Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The…

A: C=5 mD=3 md=3 mTmax=4 KNμ=0.3N=700 rpmVelocity of belt, V=π*d*N60V=π*3*70060=109.95 m/s

Q: Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a…

A: Given   Torque, T = 400 lb     Friction = 0.7       Radius = 4 in Find  Force, P

Q: The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top…

A: Given: Diameter of the piston→D=400 mm=0.4 m So area of the piston→A=π4×D2=π4×0.42=0.125 m2 Pressure…

Q: An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The…

A: (a) Since the moment is in anti-clockwise direction, the rope is stretched that is attached to the…

Q: Direction: Solve the following problems completely. Include all FBD with proper labels. 4 decimal…

A:

Q: The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an…

A: Given data:- outer diameter=350 mm inner diameter =250 mm The average value of the coefficient of…

Q: ch. The friction lining has a ce 25. The bore radius of friction li ilom contLacl pressur of IMI

A:

Q: 1) Find the equivalent spring, N/mm 2) Find the force, F Kl: =7 K5. =11 k K2 =8 X=10 mm К3 -9 K4 =10…

A: GIVEN DATA - A SPRING SYSTEM GIVEN WE HAVE TO FIND BOTH POINT 1 & 2

Q: The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given: The torque on the drum, T =  5 ft.lb The coefficient of friction between belt and drum, μ =…

Q: 1) Find the equivalent spring, N/mm 2) Find the force, F Kl: K5 k K2 x=10 mm K3 K4 K6 ........ .....

A: GIVEN DATA - A SPRING SYSTEM GIVEN WE HAVE TO FIND EQUIVALENT SPRING STIFFNESS AND FORCE

Q: A pulley system uses four v-section belts each with a cross-sectional area of 700mm 2, an included…

A: The maximum force (tension) in the belt can be given as -  T1 = 3×Centrifugal force500 =…

Q: pls explain to me step by step and pls dont skip any steps i will rate your answer immediately…

A: given data as per question force to be generated = 500 N dimension of a1 =100 mm dimension of a2…

Q: The wheel has a weight of 20 lb and a radius of gyration of kg = 0.75 ft. If the coefficients of…

A:

Q: The following lead screw and saddle arrangement is used to lift a load of 550 kg.   The square…

A: m = 550 Kg W = 550 × 9.81 = 5395.5 N Pitch P = 3mm Diameter d = 15 mm Coefficient of friction µ =0.2…

Q: friction The 300 Ib block shown in fig. has The imponding motion up Caused by the horiZontal foree…

A:

Q: 1. The blocks shown are connected by flexible, inextensible cords passing over a frictionless…

A:

Q: The 300 kgs truck heading east running a constant velocity of 20ft/s ,after 15 seconds when suddenly…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.