Answered: At a section in a 60 degree triangular…

At a section in a 60 degree triangular channel, the depth of water is 2.5m and the average velocity is 2.0 m/s. 1. Compute the rate of flow 2. What is the critical depth 3. Determine the type of flow

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: At the bottom of a spillway the velocity and depth of flow are 12 m/s and 1.5 m respectively. If the…

A: An apron is a garment that is worn over other clothing and covers mainly the front of the body. A…

Q: A circular conduit is to satisfy the following conditions: Capacity when flowing full is 0.13…

A: Given data,capacity when flowing full is 0.13m3/secvelocity when the depth is one quarter of the…

Q: A rectangular concrete channel (n = 0.015) is 10.5 ft wide, has a slope of 0.006, and a discharge…

A: Given data in question Width 10.5 ftDischarge 200 cfsSlope 0.006Depth 5.7 ftN = 0.015To find out…

Q: using Kennedy's theory, if the depth of flow Calculate the critical velocity (m/sec) of a channel is…

A: Given data- depth of flow y=3 mTo Find-The critical velocity Vc

Q: 30 0.5 m 0.2 m

A: Given Q=6100 l/s S=1/150

Q: Flow Through Pipes Question 2: The depth of flow for maximum velocity in a circular channel section…

A: A circular channel section- Diameter d=1.5 m.

Q: For a rectangular channel 5 m wide carrying a flow of 15 m3/s, determine the critical depth and the…

A: Given: Width of channel, b = 5 m Flow rate, Q = 15 m3/s

Q: A triangular-shaped channel is designed to carry 1.2 cu.m./s of water at a velocity of 0.99 m/s. For…

Q: A trapezoidal channel with bottom width of 3 m and side slope of IV: 1.5H carries a discharge of…

A: Bottom Width = 3 m\Side slope = 1V:1.5HDischarge = 8.0 m3/secFlow depth = 1.5 mTo Find :Froude…

Q: A right-angled triangular channel carries a flow of 16,000 l/s. The Manning's n = 0.020 and the…

Q: 11. Estimate the type of flow in a channel having cross sectional area of 50m² and top

A: To find : Type of flow in channel.

Q: 1. Water flows in symmetrical trapezoidal channel lined with asphalt has a base width of 4.8 m and…

A: Data givenBase width, B = 4.8 mSide slope = 3 H : 1 Vn = 0.015Channel drop= 0.1 m to every 100 mFind…

Q: A circular concrete sewer (n=0.013) is 1.52 m in diameter and is flowing at its maximum capacity at…

Q: For a trapezoidal open channel, the total discharge is 28 m^3/sec, bed width 6.0 m, side slope…

Q: A rectangular channel carries 6.0 m³/s. Calculate the

A: Given: A rectangular channel carrying discharge, Q=6 m3 /s width, B=4 m To calculate: critical…

Q: Velocity of flow in closed conduits are inversely proportional to the pipe diameter. Flow in…

A: Statement-1 Its not true For the Reynolds number <2000 flow is laminar for pipe For the Reynolds…

Q: 6 24 Water flows at a depth of 2 m in a 3 m wide rectangular channel. At a downstream section the…

Q: Problem- A circular pipe has a diameter of 1m, bed slope of 1 in 1000, and Manning's roughness…

A: Given, Diameter of circular pipe, D = 1m Bed slope, S = 1 in 1000 Manning's roughness coefficient, n…

Q: Water flows in a trapezoidal channel in which the bottom width is 6 m and the side slopes are 2:1…

A: The bottom width = 6 mSide slopes = 2 : 1 (H : V)n = 0.045Longitudinal slope of channel = 1.5%Flow…

Q: The channel shown in the figure below is built on a slope of 2 m/km and the surfaces are smooth…

A: Slope = S = 2mKm Manning's constant = n = .025 Depth of flow = y = 1.5m To determine - The…

Q: Determine the depth of flow in case of ximum velocity when the radius of the

A: To find : Depth of flow.

Q: 5(c) Water flows at a rate of 100 m³/s in a rectangular channel whose width is 3 m. Find the…

A: Given- Discharge Q=100 m3/s Width b=3 m It is needed to find the critical depth of the flow.

Q: The normal depth of flow of water, in a rectangular channel 1.5 m wide, is one metre. The bed slope…

A: Normal depth of the water = 1mWidth of the Rectangular channel = 1.5 mThe bed slope of the channel,…

Q: 500 mm diameter pipe is laid on a slope of 0.002 and is to carry 40 liters/sec. Using n = 0.013,…

Q: Please solve

A: Given: Width of channel, b = 3 m Flow rate, Q = 9 m3/s Specific energy, E = 2 m

Q: the incoming flow rate is 100m3/s on a rectangular channel with: depth = 3m width = 4 meters Then, a…

A: Using conjugate alternate depth formula

Q: 7. A rectangular channel, 20 feet wide, carries a discharge of 200 cfs. Compute the critical depth…

Q: A triangular channel with the most efficient proportion discharges water at the rate of 1.5 cu.m/s.…

A: Given data- A most efficient triangular channel. Q = 1.5 m3/s n = 0.018 S = 0.0021

Q: Water is flowing uniformly in a finished-concrete channel of trapezoidal cross section with a…

A: To Determine Flow rate of water through the channel, Q Correction in Question. Instead of 8 in…

Q: Example: A trapezoidal channel is 12.0 m wide and has a side slope of 1.5 horizontal: 1 vertical.…

A: The given data is shown below: Width=12mSide slope=1.5H:1VBed slope=0.0004n=0.015Depth of flow=3.5m

Q: The flow depth upstream of a sluice gate is 0.60 meters. The velocity is 0.9 m/s. a. What is the…

Q: Water is flowing at a rate of 4.5 m³/s in a trapezoidal channel whose bottom width is 2.4 m and side…

A: given-discharge Q=4.5 m3sbotom width b=2.4 mside slope n=2 H:1 V=2channel slope S=0.0001

Q: ind the critical depth of flow for a trapezoidal channel with a bottom width of 8 m, and a side…

A: Any of the designing of the Trapezoidal cross-section is basically done for the critical flow…

Q: A circular pipe has a diameter of 1m, bed slope of 1 in 1000, and Manning's roughness coefficient…

Q: For a rectangular channel with depth 1.2 m and 1.8m wide S=0.002 and n=0.012 ,what would be the…

Q: 0.0025

A: Area of the channel :A=120.25×2×0.25×tan60=0.108253m2Perimeter :P=0.25cos60=0.5m

Q: Calculate the critical velocity (m/sec) of a channel using Kennedy's theory, the depth of flow is 3…

A: Critical velocity is that velocity at which neither silting nor scouring take place. The channel is…

Concept explainers

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.

Question

100%

At a section in a 60 degree triangular channel, the depth of water is 2.5m and the average velocity is 2.0 m/s.
1. Compute the rate of flow
2. What is the critical depth
3. Determine the type of flow

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Time and time related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Hand written please
Water is flowing steadily in a 0.5m wide rectangular open channel at a rate of 0.3 m3/s. If the flow depth is 0.20 m, determine the flow velocity and if the flow is subcritical or supercritical. Also determine the alternate flow depth if the character of flow were to change. 5.55/s, supercritical, 1.24m B 3.33m/s, supercritical, 0.69m C) 3.44m/s, subcritical, 0.87m None of the above
Do attempt all parts.
10.45 Water flows down a wide rectangular channel having Manning's n = 0.015 and bottom slope = 0.0015. Find the rate of discharge and normal depth for critical flow conditions.
Determine the minimum depth in a 4-m-wide rectangular channel if the flow is to be subcritical with a flowrate of Q=60 m3/s.
Uniform flow occasionally occurs in a 5-m-diameter circular concrete conduit but the depth of flow can vary. The Manning's coefficient is n = 0.013, and the channel slope is 0.0005. (a) Calculate the discharge for y = 3 m, (b) Plot the discharge-depth curve.
Q2[40 p]. Water flows through the rectangular open channel in below figure that is 4 m wide. The average velocity 2.0 m/s and depth of flow is 1.5 m at first section. a) Determine the total discharge, and unit discharge. b) Determine the critical depth "Y." of flow. c) Draw Y. depth at each section. d) Classify the flow at section 1. e) If flow is critical flow at second section, show all water depths on figure. y= 1,5 m V=2.0 m/s Sol So2 So3 y b=4m
asap pls
e9
7. Water flows in a 3m wide rectangular channel. If the critical depth was measured to be 0.542m, what is the maximum flow?
The canal cross section have Manning's n values of 0.025 The uniform channel slope is 0.004. Determine the flow rates when water depths are 5ft (1.52m) above the channel bottom. Depth 5 ft 100 ft ➜
Question 8 The flow rate is 60 m/s for a rectangle channel. If the flow slope is 0.001 and roughness n = 0.02, determine the depth for an efficient section in meters.