at a point upstream of the throat in a converging-diverging nozzle the velocity temperature and pressure are 174 m/s , 23C°, 300 kpa , respectively. if the nozzle is operating at its design condition and has an exit area of 0.012 m^2 and discharge to the atmosphere with a pressure of 110 kpa determine the mass flow rate and the the nozzle throat area

at a point upstream of the throat in a converging-diverging nozzle the velocity temperature and pressure are 174 m/s , 23C°, 300 kpa , respectively. if the nozzle is operating at its design condition and has an exit area of 0.012 m^2 and discharge to the atmosphere with a pressure of 110 kpa determine the mass flow rate and the the nozzle throat area

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A- Blood flow from the left ventricle into the aorta can be modeled as a reducing nozzle (Figure below). Model both the left ventricle and the aorta as a tube with diameter of 3.1 and 2.7 cm, respectively. The pressure in the left ventricle is 130 mmHg and the pressure in the aorta is 123 mmHg. Blood is ejected from the left ventricle at a speed of 120 cm/s. Calculate the difference in height between these two locations. V2 Az = ? Aorta location 2 Left ventricle location 1
An in-compressible ideal fluid flows at 15L/s through a circular pipe into a conically converging nozzle. Determine the average velocity of flow at sections A and B of the figure below.
A water pump dissipates power on the shaft N=5.5 kW. Refine parameters: Head, flow and efficiency of the pump. Knowing the residual pressure Pair = 20, open the pump outlet (head) and the vacuum pressure at the inlet Pa,= 4m (head). The velocity in the thrust tube v2=4 m/s, the ejector tube diameter 75 mm, the suction pipe diameter 100 mm and the difference between the vacuum gauge and the manometer zero. Kinetic correction factor, geometry (Z2) -Z0). Ignore the height POST
A water jet with velocity of 15 m/sec leaving the 10 cm diameter nozzle strike to the plate in normal direction. Upon impact with the plate, the water is equally divided into two parts, i.e. one half leaves at 60° with respect to horizontal and the other half in a straight vertical direction. The density of water is 1000 kg/m3. Find the velocity at outlet neglecting change in elevation between inlet and outlet, gravity and friction between water and plate. Show your control volume
Water enters a tank of diameter DT steadily at a mass flow rate of min. An orifice at the bottom with diameter Do allows water to escape. The orifice has a rounded entrance, so the frictional losses are negligible. If the tank is initially empty, (a) determine the maximum height that the water will reach in the tank and (b) obtain a relation for water height z as a function of time?
A Francis turbine is installed with a vertical draft tube. The top of the draft is 1.0 m below thecenter line of spiral casing while the tail race water level is 3.0 m from the top of the draft tube. There is no velocity of whirl at the top or bottom of the draft tube and leakage are negligible. Theelevation of water from the reservoir to the center line of the turbine spiral casing is 50 m, and watervelocity at the inlet is 5 m/sec. Discharge is 2.5 cu.m/sec, hydraulic efficiency is 86%, overallefficiency of 83%. Determine the reading of a pressure gage (in psi) if one is installed at thepenstock just before the water inlet to the turbine.
Methane in the gaseous state flows at a rate of 0.072 m^3/s in a pipe at a temperature of 27°C and gauge pressure of 148.675kPa (point 1). The pipe is divided into two branches (point 2 and 3), as seen in the figure. If the exit velocity in pipe 3 is 12 m/s with a density of 1.9 kg/m^3, what is the flow rate and velocity in pipe 2? Consider that in section 2 the fluid is leaving with a temperature of 402°C and an absolute pressure of 175 kPa. We have an atmospheric pressure of 101.325 kPa and R_methane = 0.5182 kJ/kg ⚫K. (1) Inflow D1 D3=50mm D2=100mm (3) (2)
Air flows steadily from a large tank, through a hose of diameter D = 0.03 m and exits to the atmosphere from a nozzle of diameter d = 0.01 as shown. The pressure in the tank remains constant at 3.0 kPa and the atmospheric conditions are standard absolute temperature and pressure. Determine the flowrate and the pressure in the hose.
A horizontal-shaft centrifugal pump lifts water at 65°C. The suction nozzle is one meter below pump centerline. The pressure at this point equals 200 kPa gauge and velocity is 3 m/s. Stream tables show saturation pressure at 65°C is 25 kPa, and specific volume of the saturated liquid is 0.001020 m³kg. The pump Net Positive 1m Suction Head (NPSH) in meters is: