Assuming that member DAC is rigid and given the modules of elasticity, area, and the unstretched length of the two cables that are holding the rigid member (16 in for both), determine the reaction forces at pin A and the tension developed in each of the cables after the 400 lb is applied at point D.

Q: D В Bm 4m 3m A E G H 3m 3m 3m 3m 30KN 60KN 90KN

A:

Q: The pin-connected frame shown consists of members ABC, DEC and EBF. It is loaded as shown. Determine…

A: Solution: The pin connected frame shown below:

Q: Calculate the forces in members BF, BE, and EF. P=30 P kN 3 m B 3 m 3 m D 1 m 3 m 3 m E

A:

Q: The cmposite beam is made of 6061-T6 aluminum (A) and C83400 red brass (B). The the height, h=40mm,…

A: Section Properties : For transformed section:

Q: 4. A tapered member that is 60 inches in length is fixed connected at both ends C and D. The system…

A:

Q: force in BJ,AI,AB

A: As the truss is symmetrical :Ay=Hy=5F2=2.5800=2000kN

Q: A built members compose of wide and two plates as shown in figure 120 mm 9 mm 200 mm 10 mm 10 mm 310…

A: given datafigure is given FINDA) moment of inertia along x axisB) maximum flexural stress if the…

Q: The cantilevered W530 x 150 beam shown is subjected to a 8.5-kN force F applied by means of a welded…

A: F=8.5kN To find equivalent couple force system at point O

Q: Please show your complete solution for upvote. Please typewritten. Thank you!

A:

Q: What is the vertical  reaction at hinge support? What is the horizontal reaction at hinge support?

A: Length of the span AB -  LAB = 242 + 102⇒LAB = 26m   Taking the span Ab as the horizontal for the…

Q: Determine force in member AB

A: Consider the figure, Here, T is the tension and C is the compression.

Q: tion. The tie rod is connected at B and C by 20-mm-diamet h of 220 MPa, and each of the pins has an…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Classify each of the structures as statically determinate, statically indeterminate, stable, or…

A:

Q: A tapered member that is 60 inches in length is fixed connected at both ends C and D. The system is…

A:

Q: The frame system shown below consists of two, 3-m radius, frictionless pulleys at points B and D.…

A: Given  -

Q: TENI Q P 160 KN Beam S Hinge 2m 2 m- R

A: Given.  Load = 160 kN PQ = 2 m QR = 4 m

Q: Q-3: For the beam shown in figure, the bending moment at A will be frrth and at B will be 30 kN-m 3…

A: To Determine Bending moment at A & B

Q: for the given truss, calculate the support reaction at A in kips. express your answer in 2 decimal…

A:

Q: Civil Engineering What is the redundant force Dx used if the following primary structure solved by…

A:

Q: T in the rope is :

A: Given:  System of ropes To find: Tension T1

Q: View Policies Current Attempt in Progress A load of P = 150 kN is supported by a structure…

A: Given:- P=150 KNEb=100 GPaEs=200 GPaLength of bronze rod, L1=2250 mmDiameter of bronze rod, d1=28…

Q: From the given beam: Determine the vertical reaction at the roller support. 5000 lb 4000 lb 1000…

A: A beam arrangement is given in the question above, and it has been asked in the question to…

Q: 1.) Determine the force in each member (and identify whether it is compression or tension) of the…

A:

Q: In each case, identify any two-force members, and then draw the free-body diagrams of each member of…

A: Following are the conditions for two force members:

Q: 8 kN C 2m 1 (3) 15 kN - 2m- -2m-

A:

Q: The idealize model for suspension bridge is shown in the figure. The truss are pin connected at a,…

A: We have to determine the design diameter of the cable if the allowable tensile stress is 150 MPa and…

Q: Joints IJ,K,L,Q and M of the frame shown in the figure (not drawn to the scale) are pins. Continuous…

A:

Q: For the post-tensioned beam shown in the figure find the maximum usable moment capacity at midspan.…

A: material properties f'c= 5ksi,                                          fpu= 270 ksi,…

Q: Im 0.5 m 0.5 m 0.5 m B D 1 m- 0.5 m E

A: carrier system is givensupported at A and CG=2KNFindthe vertical support reactions and the rod…

Q: Le Lo + The steel structure is loaded as shown. hc = 4 m, Lb = 3m, P = 40 KN, E = 200 GPa, I = Ic=…

A: Since C is a roller support hence can't provide  horizontal reaction(HC =0) against the load But it…

Q: The truss is supported on rollers at A and hinge at B. Calculate the normal reaction at A and…

A:

Q: oblem Number 3: e Frame is hinged at rigid supports in A & E. Find the components of the Reaction at…

A: To find reaction at support

Q: Determine reactions at A and B, weight at end of the rope is 25 lb

A:

Q: PLEASE ANSWER ASAP!!! PROVIDE FBD FOR THE PROBLEM. ANSWER THE FOLLOWING CORRECTLY BY PROVIDING CLEAR…

A:

Q: PROBLEM NO. 3. DETERMINE ALL THE FORCES ACTING ON THE PINS OF THE GIVEN FRAME. 300 N 3 M 3 M E 2 M 2…

A:

Q: 0.6 m Answers: A- 0.5 m 0.5 m 0.5 m-77 kg E-i 42214 tude of the pinn F-422.14 N N N

A: Mass of block (m)=77kg

Q: a. b. C. d. agn roller hinge H pin cable B hinge

A: A statically determinate structure is one that is stable and all unknown reactive forces can be…

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.