Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than o= 81962 N/m2 is imposed on it. What is the maximum force (in Newton) that can be exerted on the femur bone in the leg if it has a minimum effective radius r=0.01 m? A. 25.75 B. 5.074 C. 12.87 D. 51.5 E. None

Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than o= 81962 N/m2 is imposed on it. What is the maximum force (in Newton) that can be exerted on the femur bone in the leg if it has a minimum effective radius r=0.01 m? A. 25.75 B. 5.074 C. 12.87 D. 51.5 E. None

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

question 18
Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than 0= 62780 N/m2 is imposed on it. What is the maximum force (in Newton) that can be exerted on the femur bone in the leg if it has a minimum effective radius r-0.01 m? A. 9,861 B. None C. 4.441 D. 19.72 E. 39.45
What force is required to stretch a steel wire 1 cm² in cross section to double its length, if stress is directly proportional to strain and the modulus of elasticity is 2x10" N/m?? O a. 2 x 106 N O b. 2 x 107 N O c. 3 x 107 N O d. 3 x 106 N
A ball of mass m and charge +q hang with non-conducting string of length L from a very large vertical plane wall with uniform surface charge density +o. At equilibrium the string makes an angle e with the vertical as shown in the figure. If g is the gravitational acceleration, find the angle 0. a. gen e sin omg b. 0 = sin 2omgeo 2Lmgeo 0-tan go Od. go 0 = tan 2mgeo go e. 8= cos Lmgeo Ne
Hello, I need some help with this problem.
Consider a steel rod with radius r and length L subjected to a constant tensile force T. If the radius is doubled and the length and applied tensile force is kept the same, which of the following best describes what will happen to the rod’s modulus of elasticity? A. There is not enough data to make a conclusion. B. Its value will be double the original. C. Its value will be half the original. D. Its value will remain constant. Consider a steel rod with radius r and length L subjected to a constant tensile force T. If the length of the rod is doubled and everything else is kept the same, which of the following best describes what will happen to the value of the rod’s experienced internal strain? A. Its value will remain constant. B. Its value will be half the original. C. There is not enough data to make a conclusion. D. Its value will be double the original.
05. The homogeneous 600-lb plate is suspended from three cables. Determine the tension in each cable. F1. -1.5-1 IB C 1.5 2.5 A Dimensions in feet
A wire has a diameter of 0.01 m and the original length of 3 m. The string is pulled by a force of 467 N. Determine the change in length of the string (in m). Young's modulus of the wire = 5 x 10° N/m2 O a. None of the choices O b. 0.004 O c.0.001 d. 0.000 O e. 0.011
A soccer player plants their foot on the ground and their femur rotates relative to the tibia causing the ACL to rupture. What types of stress was most responsible for the ACL to tear? A. Tension B. Torsion C. Compression
7. Carbon steel is tested in uniaxial tension, as shown in the inset schematic, to produce the following stress-strain diagram. 600 500 MPa 600 g 400 400 300 200 200 100 0.005 0.05 0.10 0.15 Strain E Figure 1: Stress vs. strain for plain carbon steel. Note: the inset shows the initial portion of the data, magnified for clarity. a) From the Figure 1, determine the following material properties: (i) elastic modulus, E, (ii) ultimate tensile strength, UTS, (iii) yield stress, oy. b) Label the following regions or points on the figure: (i) fracture point, (ii) plastic region, (iii) elastic region. 8. You wish to design a new bone screw used to hold fractured bone segments together or to hold implants in place. Describe what type of material you would use and what considerations you need to make. 27°F Cloudy Stress (MPa) a
An Aluminum cable of length 2.5 m has 15,000 N tensile force acting on it, if the wire is only allowed to be stretched by 3 mm before it breaks, X 18. what must be the radius of the wire if the Young's modulus of Al is 6.9 x 10¹⁰ N/m² ? d. 0.76 cm a. 1.32 cm b. 1.52 cm c. 1.07 cm
QUESTION 15 An 80-cm-long, 1.0-mm-diameter steel guitar string must be tightened to a tension of 2.0 × 103 N by turning the tuning screws. By how much is the string stretched, in mm? The Young's modulus for steel is 20 × 1010 N/m². Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.