Assume that we have the following fuel-cost curves for three generating units C₁(PG1) = 500+ 16 PG1 + 0.008 PG₁² C2(PG2) = 450+ 12 PG2+0.001 PG2² C3(PG3) = 300+10 PG3+0.002 PG3² 150 ≤ PG1 ≤ 500 MW 80 ≤PG2 ≤ 330 MW 100 ≤PG3 ≤ 350 MW Also assume that the network loss is related to the generators output as; Ploss 0.16(PG2-8)+0.01 (PG3-52) Find the optimal dispatch of units and the total cost in dollars/hr considering network losses when the total load, PD, is 900 MW.

Assume that we have the following fuel-cost curves for three generating units C₁(PG1) = 500+ 16 PG1 + 0.008 PG₁² C2(PG2) = 450+ 12 PG2+0.001 PG2² C3(PG3) = 300+10 PG3+0.002 PG3² 150 ≤ PG1 ≤ 500 MW 80 ≤PG2 ≤ 330 MW 100 ≤PG3 ≤ 350 MW Also assume that the network loss is related to the generators output as; Ploss 0.16(PG2-8)+0.01 (PG3-52) Find the optimal dispatch of units and the total cost in dollars/hr considering network losses when the total load, PD, is 900 MW.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
A high-voltage direct-current generating station delivers 5 MW of power at 178 kV to a city, as depicted in Figure below. The city is represented by resistance R₁ and each of the two wires of the transmission line between the generating station and the city is represented by resistance RTL. The distance between the two locations is 1752 km and the transmission lines are made of 7 cm diameter copper wire. Determine how much power is consumed by the transmission line. Please enter your answer 2 decimal places and in terms of Watt. (for copper-1.72 x 10-8) Vo Station RTL RTL ww RL (city)
Problem 3. Referring to figure shown below, determine the following using Nodal Method: (use a reference node "d") a. Nodal Voltage Va, Vb, Ve and Va if Va will serve as a reference point or zero potential. b. Branch current 11, 12, 13, 14, Is, and 16 502 + 9V 402 www - 12 202 ww 12V 10V 4|F 302 2 4V 602 www 13 С 6V
Using Figure 1, Vs 50V-15 339 Hz R1 $1100 R2 100 www XL1 320 HH XC1 Figure 1 700 R3 600 13 R4 400 XL2 1902 XL3 450 XC2 650 a. Determine the total circuit impedance, ZT. b. Calculate current IT. c. Calculate currents I, and I3. State the value of these currents in both rectangular and polar form. d. For each of the currents determined in part c, answer the following: Is the current leading, lagging, or in phase with the source voltage. e. Use the voltage-divider rule to determine the voltages across XL1 and Xc2.
Three identical Y-connected loads, each having a resistance of 20 22 in parallel with an inductor, are connected to a three phase supply of 400 V and 50 Hz frequency. The power absorb by the load is 8 kW and power factor at the load is 0.9919. (i) Determine the current that flows through the inductor. Please state the assumptions used to solve the question. Calculate load inductance in Henry (H).
Given dF₁/dP₁ = 20 +0.4P₁, dF₂/dP₂ = 30 +0.4P2, and Poss = 0.0004P2 + 0.0006P2² Assume the load = 1000 MW. Using the coordination equation method, and starting with P = 500MW, P = 500MW Perform one iteration to get: Select one: O a. None of these b. P₁ = 775MW, P₂ = 475MW, andλ = 550$/MWh O c. P₁ = 675MW, P₂ = 575MW, andλ = 450$/MWh O d. P₁ = 875MW, P₂ = 375MW, andλ = 650$/MWh
Question is attached
moduleMSX-83fromBPsolarisusedinthefollowingconfigurationtomakeaPVarray: •4modulesinseries •2strings(of4modulesinseries)inparallel TheelectriccharacteristicsatSTCaregivenbelow: Maximumpower(Pmax)=83W Short-circuitcurrent(Isc)=5.27A VoltageatPmax(Vmp)=17.1V Open-circuitvoltage(Voc)=21.2V CurrentatPmax(Imp)=4.85A WhatwillbetheelectriccharacteristicsofthePVarray?
Course:Power generation and control Please solve in detail to understand
b) Indicate the following characteristics on the generic second order response given in Figure Q3(b). i. ii. iii. iv. Rise Time Settling Time Min Settling Time Max Settling Time V. Overshoot vi. Undershoot vii. viii. Maximum peak Peak Time Amplitude 4 3.5 3 2.5 2 1.5 H 1 0.5 0 0 5 Step Response ܫܚܢ 10 Time (seconds) Figure Q3(b) 15 20 25
For the circuit given in Figure 1, a) Find the Thevenin equivalent circuit with respect to terminals a-b b) When a 5000 resistor is connected to terminal a-b, find the voltage on the resistor wwwwwwmm c) It will be connected to a-b terminals and its voltage on 5000 load will be 132 kV rms. What should be the capacitive reactance value that will increase it? wwwwwwwww d) What happens to the short-circuit current when the a-b terminals are short-circuited? 2+1202 000 m da 127/6 kV rms ob 1.5 +/902 000 w 12725 kV ms
Develop the mathematical relationships for the design of the inductance and capacitance of a three-phase double circuit line. A three-phase double circuit line consists of two identical three-phase parallel circuits as shown in the figure below. The circuits are operated with a1-a2, b1-b2, and c1-c2 in parallel.