Assume that if the shear stress in steel exceeds about 4.00 × 108 N/m², the steel ruptures.(a) Determine the shearing force necessary to shear a steel bolt 1.50 cm in diameter.(No Response) N(b) Determine the shearing force necessary to punch a 1.50-cm-diameter hole in a steel plate 0.650 cm thick.(No Response) N

Given:Shear stress, σ=4.0×108N/m2 .(a) The area of the steel bolt is, A=πr2 Diameter , d=1.50cm∴…

Answered: Assume that if the shear stress in…

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 54PQ

See similar textbooks

Similar questions

Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
The lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27
Consider a nanotube with a Youngs modulus of 2.130 1012 N/m2 that experiences a tensile stress of 5.3 1010 N/m2. Steel has a Youngs modulus of about 2.000 1011 Pa. How much stress would cause a piece of steel to experience the same strain as the nanotube?
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57
An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?
A disk between vertebrae in the spine is subjected to a shearing force of 600 N. Find its shear deformation, taking it to have the shear modulus of 1109 N /m2. The disk is equivalent to a solid cylinder 0.700 cm high and 4.00 cm in diameter.
(a) Estimate the force with which a karate master strikes a board, assuming the hands speed at the moment of impact is 10.0 m/s and decreases to 1.00 m/s during a 0.002 00-s time interval of contact between the hand and the board. The mass of his hand and arm is 1.00 kg. (b) Estimate the shear stress, assuming this force is exerted on a 1.00-cm-thick pine board that is 10.0 cm wide, (c) If the maximum shear stress a pine board can support before breaking is 3.60 106 N/m2, will the board break?
What Is Static Equilibrium? Problems 13 are grouped. 1. C A ball is attached to a strong, lightweight rod (Fig. P14.1). The rod is supported by a horizontal pin near the top. The ball is at rest. Is the ball in static equilibrium? If not, why not? If so, which type of equilibrium is itstable, unstable, or neutral? Hint: What would happen if you displaced the ball slightly? FIGURE P14.1
(a) The "lead" in pencils is a graphite composition with a Young's modulus of about 1109 N/ m2. Calculate the change in length of the lead in an automatic pencil if you tap it straight into the pencil with a force of 4.0 N. The lead is 0.50 mm in diameter and 60 mm long. (b) Is the answer reasonable? That is, does it seem to be consistent with what you have observed when using pencils?
Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial diamond of volume 1.00 106 m3 is formed under a pressure of 5.00 GPa. Find the change in its volume when it is released from the press and brought to atmospheric pressure. Take the diamonds bulk modulus to be B = 194 GPa.
A steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the ceiling a 10.0-kg model aircraft that is flying in a horizontal circle with an angular speed of 6.00 rad/s. What is the strain produced in the cable?

SEE MORE QUESTIONS

Recommended textbooks for you

Physics for Scientists and Engineers: Foundations…

Physics

ISBN:

9781133939146

Author:

Katz, Debora M.

Publisher:

Cengage Learning

Physics for Scientists and Engineers, Technology …

Physics

ISBN:

9781305116399

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Physics for Scientists and Engineers

Physics

ISBN:

9781337553278

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Physics for Scientists and Engineers: Foundations…

Physics

ISBN:

9781133939146

Author:

Katz, Debora M.

Publisher:

Cengage Learning

Physics for Scientists and Engineers, Technology …

Physics

ISBN:

9781305116399

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Physics for Scientists and Engineers

Physics

ISBN:

9781337553278

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Physics for Scientists and Engineers with Modern …

Physics

ISBN:

9781337553292

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

College Physics

Physics

ISBN:

9781938168000

Author:

Paul Peter Urone, Roger Hinrichs

Publisher:

OpenStax College

University Physics Volume 1

Physics

ISBN:

9781938168277

Author:

William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:

OpenStax - Rice University

SEE MORE TEXTBOOKS