Assume that at time tm, the current in the inductor is at a maximum, at that time, the current flows from point b to point a. At time tm, which of the followingstatements is true?▸View Available Hint(s)O The voltage across the inductor must be zero and increasingThe voltage across the inductor must be zero and decreasing.O The voltage across the inductor must be positive and momentarily constantO The voltage across the inductor must be negative and momentarily constant

In electrical engineering, an inductor's behavior at particular times can reveal important…

Assume that at time tm, the current in the inductor is at a maximum, at that time, the current flows from point b to point a. At time tm, which of the following statements is true? View Available Hint(s) O The voltage across the inductor must be zero and increasing. O The voltage across the inductor must be zero and decreasing. O The voltage across the inductor must be positive and momentarily constant O The voltage across the inductor must be negative and momentarily constant.

Assume that at time tm, the current in the inductor is at a maximum, at that time, the current flows from point b to point a. At time tm, which of the following statements is true? View Available Hint(s) O The voltage across the inductor must be zero and increasing. O The voltage across the inductor must be zero and decreasing. O The voltage across the inductor must be positive and momentarily constant O The voltage across the inductor must be negative and momentarily constant.

Operations Research : Applications and Algorithms

4th Edition

ISBN:9780534380588

Author:Wayne L. Winston

Publisher:Wayne L. Winston

Chapter11: Nonlinear Programming

Section11.2: Introductory Concepts

Problem 3P

See similar textbooks

Similar questions

Three balls, with masses of (m;=1 kg, m2=2 kg, m3=3 kg), are fastened to a massless rod of length L=30 cm as shown. The moment of inertia (in kg. m?) about the left end of the rod is: L/2 L/2 Im3 m2 O a. 0.135 O b. 0.015 O c. 0.06 O d. 0.24
I A bob attached to a cord is moved to the right where its vertical position is 1.05 cm above the equilibrium position and is then given an initial speed of 0.6 m/s. What are the values of the maximum speed and maximum height reached by the bob? (Take g = 9.8 m/s') (a) hmax (b)hmax =D1.87 cm; tnax 3.44 m/s (c) hmax (d) hmax 2.89 cm; Vnax = 0.75 m/s 1.87 cm; max 0.75 m/s 2.89 cm; 1,ax 3.44 m/s or frequency to 2/:
The electric flux density D at the point M (0,4,0) in the region about a uniform line charge of 1 nC/m lying along the z axis in free space is: Select one: a. None of the above b. 0.6366 nC/m c. 0.2387 nC/m d. 0.039 nC/m e. 0.1 nC/m
As an OCTAVE pogram: A 1 kg mass is rests on a frictionless 1 meter long ramp and compresses a k = 4000 N/m spring a distance of 5 cm. The ramps angle of incline varies from 10 to 50 degrees, in increments of 10 degrees. For each angle of incline, determine if the block will slide off the top end of the ramp after it is released from the Spring. Output each angle of incline and whether of not the block reaches the top of the ramp.
Solve both the questions!!!
b Mra. Q5. A cylinder is 150 mm mean diameter and 750 mm long with a wall 2 mm thick. It has an internal pressure 0.8 MPa greater than the outside pressure. Calculate the following. E=200 GPa H i. The circumferential strain. ii. The longitudinal strain. EL iii. The change in diameter. iv. The change in length. L iv. The change in volume v 2:0.3 أطلبوها من مكتب لكلمات Q6. The thin walled cylinder can be supported in one of the two ways as shown. Determine the state of stress in the wall of the cylinder for both cases if the piston P causes the internal pressure to be 500 KPa. The wall has a thickness of 5 mm and the inner diameter of the cylinder is 200 mm. 2) Piston Piston 百货
Solve both
An aluminum wire having a cross-sectional area equal to 4.60 x 10-6 m? carries a current of 7.50 A. The density of aluminum is 2.70 g/cm³. Assume each aluminum atom supplies one conduction electron per atom. Find the drift speed of the electrons in the wire. 1.95E-4 The equation for the drift velocity includes the number of charge carriers per volume, which in this case is equal to the number of atoms per volume. How do you calculate that if you know the density and the atomic weight of aluminum? mm/s
2. calculates the trajectory r(t) and stores the coordinates for time steps At as a nested list trajectory that contains [[xe, ye, ze], [x1, y1, z1], [x2, y2, z2], ...]. Start from time t = 0 and use a time step At = 0.01; the last data point in the trajectory should be the time when the oscillator "hits the ground", i.e., when z(t) ≤ 0; 3. stores the time for hitting the ground (i.e., the first time t when z(t) ≤ 0) in the variable t_contact and the corresponding positions in the variables x_contact, y_contact, and z_contact. Print t_contact = 1.430 X_contact = 0.755 y contact = -0.380 z_contact = (Output floating point numbers with 3 decimals using format (), e.g., "t_contact = {:.3f}" .format(t_contact).) The partial example output above is for ze = 10. 4. calculates the average x- and y-coordinates 1 y = Yi N where the x, y, are the x(t), y(t) in the trajectory and N is the number of data points that you calculated. Store the result as a list in the variable center = [x_avg, y_avg]…
Two small charged objects attract each other with a force F when separated by a distance d.If the charge on each object is reduced to one-fourth of its original value and the distance between them is reduced to d/2,the force becomes?
When a tension force of 900 N is applied to a steel wire, it is assumed that E = 210 GPa and that the diameter of the wire increases by 1.05 mm. Calculate the diameter of the wire.
During a journey, a car accelerates from (10 m/s) to (20 m/s) in (5 sec). Calculate the acceleration of the car: 2.5 О 3.0 1.5 2.0 A bullet of mass 20g is found to pass two points 30m apart in a time interval of 4s. Calculate the kinetic energy of the bullet if it moves with constant speed. * 0.562J O 5J 2J O 2.5J