Assume that a max deflection is equal to (length/1000)mm is to be the limiting factor in selecting a W-beam having a span length of 1.35 meters. Fixed at one end and the load at the free end is 20.60kN. I=73,320,591mm^4. Determine the minimum material stiffness( Young's Modulus) in GPa

Q: 30 kN 20 kN/m 2 m -3m 2. If the size of beam in Problem I is 150mm x 300mm and E = 15 GPa, what is…

A: E=15GPa

Q: 102 kN/m L/4 L 8 meter

A: Free body diagram -  Due to symmetry of forces reaction force at both the ends is same-  RF = RG =…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: X kN/m A 5 m 5 m Figure 2: Simply supported beam A 10 meter simply supported beam made of A-36 steel…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: Problem 3 The bar CBA is axially loaded by force P at end A and by force Q at section B. The entire…

A: Given data,  P = 4 kN E = 70 GPa Lab = 0.4 m Lbc = 0.5 m

Q: The 9m beam in figure 05 is loaded as shown. The location of maximum deflection measured from the…

A: Reaction calculation:Ra+Rb=0.5×2×9=9kNMoment about A =0Rb×9-9×23×9=09Rb=54Rb=6kNRa=3kN Rate of…

Q: A simply supported beam with length l is loaded with a uniformly distributed load w. What is the…

A: A simply supported beam is the beam that stays on two supports and is free to move horizontally. It…

Q: Question #3 For the beam shown in Figure 3, a) Determine the maximum compressive bending stress in…

A:

Q: scontinuity functions to compute (a) the slope of the beam at B and (b) the deflection El = 27 x 106…

A:

Q: Part 2: By Super Position Consider the simple supported beam shown in the Fig. a. Determine the…

A:

Q: Using the "Effects Overlay" of the original beam, using isostatic sub-beams and simulating them…

A: Given that :- Modulus of Elasticity (E) = 200 GPa = 200,000 MPaWeight of the beam (W) = 2.5 Applied…

Q: A simply supported beam, 6m in length, has an initial deflection of 0.50mm at midspan due to its own…

A: For a simply supported beam having UDL maximum deflection at center is given as  ∆=5 wL4384 EI where…

Q: A simply supported beam, 6m in length, has an initial deflection of 0.50mm at midspan due to its own…

A: Given That  L= 6m Δmax=0.5mm =0.0005m Let us assume the own weight is "w"  kN/m E = 24870MPa I =…

Q: A simply-supported beam, 9 m in length, is subjected to a uniform load of 20 kN/m applied at the…

A:

Q: Derive an expression for the maximum value of deflection for the simlply supported beam.

A:

Q: b) In Figure Q1, an axial load P is applied at point D that is 5 mm from the geometric axis of the…

A: Iy = π/64(1204 - 1124) = 2.455 x 106 mm4  L = 2.8 m = 2800 mm

Q: For the beam shown, solve for the deflection (in mm.) at B. Use the following data: W = 3.2 kN/m L=…

A:

Q: W = 30 K/m L= 3m E- 18GPA;b=200 mm %3D d: 400 mm

A:

Q: Solution accu

A:

Q: ows an elastic be igidity EI and deflection v(x) d by an equation

A:

Q: A cantilever beam subjected to uniform variable load, if the beam is made of I Beam having a…

A:

Q: Consider the stress element as shown in figure. Determine the total distortion energy stored in 1 m…

A: For given state of stress,Young’s modulus of elasticity as E= 2 × 105 MPaPoisson’s ratio  0.3.

Q: Following using the double integration method: d. The deflection at the middle of the beam e. The…

A:

Q: A cantilever beam, having a length of 7.0 m, carries a uniformly distributed dead load of 10 kN/m,…

A:

Q: The plastic block shown is bonded to a fixed base and to a horizontal rigid plate to which a force P…

A: Therefore, the deflection of the plate is 0.0709 inches.

Q: Give me right solution with clear calculations.  Use moment area method

A: Asked 1. To determine deflection at free end using moment area method

Q: A steel beam is loaded as shown in the figure. Use conjugate beam method and determine the…

A: A Conjugate beam is an imaginary beam with and same geometrical properties as the real beam. The…

Q: The part shown below is formed from 3-mm diameter steel wire with R = 40 cm. A force is applied with…

A: Given data in question  Load Dimensions  Diameter  Radius To find out  Horizontal deflection at C…

Q: A= h Ph³ 351 PROVE THAT A = Ph² 3E1 BY: SLOPE DEFLECTION METHOD

A: Given data : Cantilever beam with fixed end at A and free end at B Find : Horizontal deflection at B…

Q: 3. A steel beam is loaded as shown in the figure. Use conjugate beam method and determine the…

A: A Conjugate beam is an imaginary beam with and same geometrical properties as the real beam. The…